Subject	Re: Who was the guy who recently refinished his 3 piece wheels?
Posted by	CmyZ on May 12, 2010 at 6:47 PM
	This message has been viewed 50 times.
In Reply To	Who was the guy who recently refinished his 3 piece wheels? posted by BigTDogg (MA) on May 12, 2010 at 02:14 PM
Message	Keep sanding with 2000 until its very smooth and then hit with them with a wheel buffer with polishing compound and burn it in..unless you went to aggressive with the sanding, even still you can sand it out. Post a pic of the current state.
Follow Ups	Who was the guy who recently refinished his 3 piece wheels? - BigTDogg (MA) 14:14:51 05/12/10 Is that the gouge from NTB all those years ago? (n/m) - Dave N 14:19:05 05/12/10 I recently polished my Volks I bought used I used 3M - REDI4U 14:32:49 05/12/10 Sears, circa 2003 - BigTDogg (MA) 14:36:28 05/12/10 Wow this sounds familiar - awesom-o 20:46:30 05/12/10 you did your H2O hard pipes right? No difference.. slacker. (n/m) - Cap927(Boston) 14:41:21 05/12/10 I gotta be doing something wrong. - BigTDogg (MA) 14:53:26 05/12/10 swing by my house this weekend and we'll take a look (n/m) - Cap927(Boston) 15:22:02 05/12/10 Do you guys live in the city? - JRFITZ 16:07:53 05/12/10 I'm North of Boston (n/m) - Cap927(Boston) 16:17:18 05/12/10 Re: I'm North of Boston - JRFITZ 16:18:45 05/12/10 And you probably never see us because we're two garage - Cap927(Boston) 16:21:25 05/12/10 The picture in my profile is Nahant's 40 steps area - Cap927(Boston) 16:22:44 05/12/10 Nahant isnt far - JRFITZ 16:33:30 05/12/10 Werd up, we should all get together sometime next month (n/m) - BigTDogg (MA) 21:09:16 05/12/10 that would be cool. - JRFITZ 22:13:42 05/12/10 Once you get the surface finish where you want it - BeachZ 16:24:10 05/12/10 If you don't want to mess with the wheel there is a place in - EricTTZ 18:06:07 05/12/10 Re: Who was the guy who recently refinished his 3 piece wheels? - CmyZ 18:47:35 05/12/10 i did mine with mothers wheel polish - volcomstone550 19:45:21 05/12/10 After stepping down on paper grit you need to shift - ShakaShaun(Denver) 20:16:33 05/12/10 That's the before shot there, the small scratches on the - BigTDogg (MA) 20:50:32 05/12/10 Gotcha. I think I drill mounted wheel and a few - ShakaShaun(Denver) 21:01:07 05/12/10 I know a guy at Sears that can buff that.... Oh nevermind. - Ghozt 20:20:14 05/12/10 I've done it. - Maximamike 21:13:54 05/12/10 BTW, this is the post you were looking for. - Maximamike 21:30:03 05/12/10 That was the exact post, thanks Mike! - BigTDogg (MA) 23:03:52 05/12/10 Not bad.. - Maximamike 23:12:28 05/12/10 She runs, and she's on the road, no worries - BigTDogg (MA) 10:39:41 05/13/10 Progress shot. - BigTDogg (MA) 07:48:15 05/13/10 What about using something like this: - BigTDogg (MA) 10:56:52 05/13/10
Post a Followup	You cannot reply to this message because you are not logged in.