Subject	While I agree that some folks have had issues...
Posted by	Bernie (NoVA) on May 01, 2010 at 10:12 PM
	This message has been viewed 125 times.
In Reply To	Search? posted by Evan(CA) on May 01, 2010 at 01:41 PM
Message	there are often mitigating facts to their stories that they like to leave out... beating on the trans when not broken in dumping the factory break in fluid from the start for no reason poor pedal adjustment clutch pedal hydralics being in need of bleeding/replacement etc etc In short just because a transmission grinds (new or old) doesn't mean that the trans internals are bad - there are lots of possible factors. I've installed several of the 98+ spec units and sold & shipped more, I have not had problems with them. I would say with out a doubt that the amount of people that have installed the 98+ trans and have had zero issues with them FAR out numbers the handful of folks that have have problems (self induced or otherwise) Bernie Bilski berniebilski@cox.net 1995 Nissan 300ZX TwinTurbo in Cobalt Green 1997 Nissan 240SX SE in Ultra Red ZCCNV #390 ~ ECZA #368
Follow Ups	Box Shots - toykoz32 19:54:50 04/30/10 Talk about sexy.... (n/m) - CoHPhasor 20:40:55 04/30/10 Gorgeous. - zfreak(Dallas) 20:43:07 04/30/10 So this is the 98+ jspec, correct? (n/m) - SimaYi 20:44:56 04/30/10 Yesssss sir (n/m) - toykoz32 21:49:03 04/30/10 I'll be curious to get some feedback :) - SimaYi 23:02:15 04/30/10 Good luck with it.. I know a person that had over 600rwhp - KongZTT GT28RS MD 21:27:44 04/30/10 Damn . . . I hope there no problems with these. - toykoz32 21:55:32 04/30/10 Sadly many people have reported problems with the 98+ (n/m) - Evan(CA) 21:58:18 04/30/10 I wouldn't say many, maybe a few - toykoz32 22:09:01 04/30/10 No problems with mine... don't regret the purchase a bit. (n/m) - Multi_Read (MO) 22:14:44 04/30/10 Agreed. (n/m) - Bernie (NoVA) 22:14:30 05/01/10 many people who have replaced the break in gear oil before - Adam (NoVA) 22:35:39 04/30/10 not really (n/m) - aliaZ 04:26:04 05/01/10 Search? - Evan(CA) 13:41:50 05/01/10 While I agree that some folks have had issues... - Bernie (NoVA) 22:12:28 05/01/10 From what I've read here, a large majority of those who.. - ForceFedTT (SoCal) 01:38:40 05/02/10 WPC Treatment? Is it work doing? (n/m) - toykoz32 21:56:21 04/30/10 Its similar to shot peening.. except the media is powder - KongZTT GT28RS MD 01:54:20 05/01/10 Aren't synchros friction devices? - CaliguyPurdue (Selin Design) 10:31:56 05/01/10 Mike Kojima peddles this stuff in basically every article - FuerGrissa 18:35:21 05/01/10 Spending that kind of coin. You could have simply built - Turnerscasa (Dallas) 08:29:50 05/01/10 built the hell out of the trans with what? (n/m) - aliaZ 16:22:44 05/01/10 ppg gearset? - ali300zx 17:03:13 05/01/10 and those use oem syncros unless you go dogbox (n/m) - aliaZ 17:27:45 05/01/10 What's up, RJ? Nice trans, BTW :-) (n/m) - ForceFedTT (SoCal) 01:41:00 05/02/10
Post a Followup	You cannot reply to this message because you are not logged in.