Subject	So I tore into my engine today, because of a knock I was
Posted by	cossiemodo2000 on April 25, 2010 at 11:49 PM
	This message has been viewed 363 times.
Message	hearing above 2000 rpms. I dropped the front cross member and oil pan. removed all rod bearings, and the number 1 cylinder rod bearing was spun. I did'nt take any pictures, but the bearing was not spun soo bad, there was still plenty of friction material on it, but it was spun. I checked the crank for discoloration or scratches and there was none. I bought a new set of bearings, installed them and hope for the best. The car was not run for more than 2 miles since the knock started, and I must say it did not knock at idle at all. Do you guys think my motor will be fine? Also when I removed the oil filter I found that there was rubber inside the two little balls in the oil filter tree, could that have caused some sort of oil lubrication problem that made the bearing spin?
Follow Ups	So I tore into my engine today, because of a knock I was - cossiemodo2000 23:49:28 04/25/10 I forgot to add that this was a rebuilt motor with less than - cossiemodo2000 23:52:22 04/25/10 Re: So I tore into my engine today, because of a knock I was - Tech@EPR 02:01:17 04/26/10 the outer part of the bearing was intact - cossiemodo2000 02:12:29 04/26/10 Re: the outer part of the bearing was intact - Tech@EPR 03:43:10 04/26/10 I actually changed all the rod bearings, only the the - cossiemodo2000 03:53:39 04/26/10 Re: I actually changed all the rod bearings, only the the - Tech@EPR 03:56:26 04/26/10 Seems unlikely the rod big-end would be out of round - ZXoltan 06:08:08 04/26/10 Re: Seems unlikely the rod big-end would be out of round - Tech@EPR 08:00:48 04/26/10 the engine is still in the car - aliaZ 08:07:27 04/26/10 Re: the engine is still in the car - Tech@EPR 08:11:28 04/26/10 PlastiGage Counterpoint: - ni[X]it 09:50:32 04/26/10 Re: PlastiGage Counterpoint: - Tech@EPR 13:07:11 04/26/10 Re: PlastiGage Counterpoint: - Zarcasm(Hfd, CT) 17:30:53 04/26/10 you're probably fine - aliaZ 07:33:31 04/26/10 What makes you think its fine? - Antihero 08:55:24 04/26/10 He did mention some findings in the oil tree. - ZiNnYc 09:29:58 04/26/10 my saying it's fine is contingent on checking clearances - aliaZ 10:59:43 04/26/10 also - aliaZ 11:04:01 04/26/10 Re: my saying it's fine is contingent on checking clearances - Tech@EPR 13:14:37 04/26/10 IMO - a spun rod bearing means the rod is effed and should - LitlElvis 10:52:49 04/26/10 yes, if the rod bearing did indeed spin in the big end - aliaZ 11:02:28 04/26/10 I agree, misuse of terms = confusion for all - LitlElvis 12:23:19 04/26/10 Re: IMO - a spun rod bearing means the rod is effed and should - Tech@EPR 13:15:29 04/26/10 Re: So I tore into my engine today, because of a knock I was - 1990 tt 11:04:06 04/26/10 fwiw, my eagle rods also needed to be resized brand new (n/m) - aliaZ 11:05:30 04/26/10 On resizing brand new rods - ZXoltan 11:13:47 04/26/10 Eagle rods are good rod for the bucks - timz 12:29:28 04/26/10 Re: On resizing brand new rods - Tech@EPR 13:11:26 04/26/10 Well, they are made in China right? (n/m) - Got a Birth certificate?? 16:33:52 04/26/10 I thought all quality Z parts were made in China ;-) (n/m) - ZXoltan 17:02:09 04/26/10 got any pics? - aliaZ 11:06:57 04/26/10 sorry for not being clear, no it did not spin, it just - cossiemodo2000 15:39:33 04/26/10
Post a Followup	You cannot reply to this message because you are not logged in.