Subject	Same here. (n/m)
Posted by	Aqualung on April 15, 2010 at 2:49 PM
	This message has been viewed 118 times.
In Reply To	To expensive at this point for just a rear bumper. posted by Woody75 (Denver) on April 15, 2010 at 02:40 PM
Message
Follow Ups	TwinZ Design Rear Bumper Pre-Order Update - bryan@Z1 09:26:56 04/15/10 Also worth mentioning... - bryan@Z1 09:58:02 04/15/10 I assume you guys will be holding a back a few in case - SlicktopTT 12:06:04 04/15/10 Re: I assume you guys will be holding a back a few in case - bryan@Z1 12:41:59 04/15/10 any status on 2+2 version (n/m) - jzee32tt 13:28:09 04/15/10 considering that IIRC there are only 3 Z32's in Peru, the - LJZTT 13:35:41 04/15/10 The TwinZ have mentioned a 2+2 version themselves. (n/m) - Barry (NJ) 15:14:30 04/15/10 I didnt mean for that to come across as if I knew their - LJZTT 15:41:15 04/15/10 We already have an extremely clean 2+2 waiting to be - TheTwinZ (Peru) 20:40:20 04/15/10 good news then, I have seen a lot of posts of 2+2 owners - LJZTT 00:25:09 04/16/10 so where did you come across the 2+2? (n/m) - LJZTT 12:29:59 04/17/10 My friend has a 2+2 and has put a lot of money into it... - TheTwinZ (Peru) 14:18:04 04/17/10 To expensive at this point for just a rear bumper. - Woody75 (Denver) 14:40:22 04/15/10 Same here. (n/m) - Aqualung 14:49:36 04/15/10 Not too far off from the JSpec fascia, though... (n/m) - Z_Cherub 15:20:36 04/15/10 especially if you decide to shave it or buy pre-shaved - LJZTT 15:42:30 04/15/10 $300 difference seems far off to me. - Woody75 (Denver) 15:42:59 04/15/10 Apples and oranges if you compare TwinZ rear w/ uninstalled - Z_Cherub 15:55:16 04/15/10 huh, jspec is $600 shipped. - Woody75 (Denver) 19:17:13 04/15/10 You're correct, I was comparing - - Z_Cherub 08:13:07 04/16/10 dont you also need to shorten exhaust? (n/m) - Antihero 15:38:09 04/15/10 No. That was a different one (n/m) - na300zx (OH) 16:05:11 04/15/10 If we've already preordered, can we pay in full early? (n/m) - 96300NAZ 19:47:06 04/15/10 Yes, you can pay the balance any time you'd like. (n/m) - bryan@Z1 08:28:28 04/16/10 Dammit, dammit, dammit. I put in my order :( - Woody75 (Denver) 08:17:39 04/16/10 Glad to see you came around. The price is a little high - SlicktopTT 09:02:32 04/16/10 Re: Glad to see you came around. The price is a little high - ouikikazz 12:18:08 04/16/10 Re: Re: Glad to see you came around. The price is a little high - plower 18:34:43 04/16/10 bet you $10 when it is painted/installed you'll be all grins (n/m) - LJZTT 12:28:52 04/17/10
Post a Followup	You cannot reply to this message because you are not logged in.