Subject	pretty sure I set those into the plenum and then the rail
Posted by	LJZTT on March 12, 2010 at 5:33 PM
	This message has been viewed 46 times.
In Reply To	Yeah. I guess I did a bad job describing it... (n/m) posted by na300zx (OH) on March 12, 2010 at 04:55 PM
Message	on top of them. Maybe I haven't torqued the rail down tight enough? That would be the only explanation for the leak if what guapo says is true, right? "The American people will never knowingly adopt socialism. But, under the name of "liberalism", they will adopt every principle of our socialist program, until one day America will be a socialist nation, without ever knowing how it happened.... I no longer need to run on the Socialist Party ticket because the Democrat Party has now adopted our platform." --Norman Thomas, 1944 Socialist Party Presidential Candidate "Socialism is a philosophy of failure, the creed of ignorance, and the gospel of envy, its inherent virtue is the equal sharing of misery." --Winston Churchill
Follow Ups	She's Out..... - Jason300zxTT 22:10:12 03/11/10 luvin' Sapp Blu ...droool. - SuparexTT 22:11:31 03/11/10 Good work. (n/m) - Wright (Ca) 22:16:48 03/11/10 Pretty much assume new motor mounts when the motor is pulled (n/m) - Guapo 22:35:01 03/11/10 Agreed. (n/m) - Bernie (NoVA) 23:15:03 03/11/10 What mounts would you all go with? - Jason300zxTT 07:41:17 03/12/10 definitely not Noltec (n/m) - aliaZ 07:55:14 03/12/10 OEM (n/m) - Guapo 08:52:21 03/12/10 Heard good things about the Ford motor mounts. (n/m) - Z_Cherub 08:52:25 03/12/10 and bad things - ali300zx 09:04:01 03/12/10 Hm - good to know. - Z_Cherub 09:11:25 03/12/10 OEM for both motor and tranny mounts (n/m) - moxie (SF) 11:34:54 03/12/10 I use stockers - have 2 sets of new ones on hand. (n/m) - Bernie (NoVA) 16:51:10 03/12/10 maybe this is a given, but I didnt know about it, make sure - LJZTT 07:48:44 03/12/10 ONly way that can happen is if those were the only two - Guapo 08:52:03 03/12/10 All I know is prior to engine pull, I had eliminated all - LJZTT 12:21:21 03/12/10 What about the seals that go around the fuel rail? - na300zx (OH) 12:58:57 03/12/10 I'm not quite certain where exactly you are referring - LJZTT 16:41:22 03/12/10 Rubber isolators between the fuel rail & the lower plenum (n/m) - Bernie (NoVA) 16:52:55 03/12/10 Yeah. I guess I did a bad job describing it... (n/m) - na300zx (OH) 16:55:34 03/12/10 pretty sure I set those into the plenum and then the rail - LJZTT 17:33:42 03/12/10 Or if the rail caught the edge of one on the way down - na300zx (OH) 18:01:56 03/12/10 Pretty much impossible to get down in there and see where - LJZTT 20:43:19 03/12/10 Ive used that sling dozens of times and have never had - EricTTZ 09:16:43 03/12/10 Re: Ive used that sling dozens of times and have never had - Jason300zxTT 09:31:56 03/12/10 Nice (n/m) - BigTDogg (MA) 08:53:03 03/12/10 yup, thats oil. (n/m) - Adam (NoVA) 09:38:35 03/12/10 BTW... - Bernie (NoVA) 20:42:12 03/12/10
Post a Followup	You cannot reply to this message because you are not logged in.