Subject	ONly way that can happen is if those were the only two
Posted by	Guapo on March 12, 2010 at 8:52 AM
	This message has been viewed 55 times.
In Reply To	maybe this is a given, but I didnt know about it, make sure posted by LJZTT on March 12, 2010 at 07:48 AM
Message	bolts in the plenum at the time. Always have all the other plenum bolts torqued as well as the two side brackets installed then using this. Petz #2 "What's the point of having the car if you don't drive it?" - Mrs. Guapo 08/20/05 Jeeeesus Christ - my Dad (after a ride in my Z) 12/26/04 People have the right to freedom of expression. However, people also have the right to point and laugh- aliaZ 04/06/06
Follow Ups	She's Out..... - Jason300zxTT 22:10:12 03/11/10 luvin' Sapp Blu ...droool. - SuparexTT 22:11:31 03/11/10 Good work. (n/m) - Wright (Ca) 22:16:48 03/11/10 Pretty much assume new motor mounts when the motor is pulled (n/m) - Guapo 22:35:01 03/11/10 Agreed. (n/m) - Bernie (NoVA) 23:15:03 03/11/10 What mounts would you all go with? - Jason300zxTT 07:41:17 03/12/10 definitely not Noltec (n/m) - aliaZ 07:55:14 03/12/10 OEM (n/m) - Guapo 08:52:21 03/12/10 Heard good things about the Ford motor mounts. (n/m) - Z_Cherub 08:52:25 03/12/10 and bad things - ali300zx 09:04:01 03/12/10 Hm - good to know. - Z_Cherub 09:11:25 03/12/10 OEM for both motor and tranny mounts (n/m) - moxie (SF) 11:34:54 03/12/10 I use stockers - have 2 sets of new ones on hand. (n/m) - Bernie (NoVA) 16:51:10 03/12/10 maybe this is a given, but I didnt know about it, make sure - LJZTT 07:48:44 03/12/10 ONly way that can happen is if those were the only two - Guapo 08:52:03 03/12/10 All I know is prior to engine pull, I had eliminated all - LJZTT 12:21:21 03/12/10 What about the seals that go around the fuel rail? - na300zx (OH) 12:58:57 03/12/10 I'm not quite certain where exactly you are referring - LJZTT 16:41:22 03/12/10 Rubber isolators between the fuel rail & the lower plenum (n/m) - Bernie (NoVA) 16:52:55 03/12/10 Yeah. I guess I did a bad job describing it... (n/m) - na300zx (OH) 16:55:34 03/12/10 pretty sure I set those into the plenum and then the rail - LJZTT 17:33:42 03/12/10 Or if the rail caught the edge of one on the way down - na300zx (OH) 18:01:56 03/12/10 Pretty much impossible to get down in there and see where - LJZTT 20:43:19 03/12/10 Ive used that sling dozens of times and have never had - EricTTZ 09:16:43 03/12/10 Re: Ive used that sling dozens of times and have never had - Jason300zxTT 09:31:56 03/12/10 Nice (n/m) - BigTDogg (MA) 08:53:03 03/12/10 yup, thats oil. (n/m) - Adam (NoVA) 09:38:35 03/12/10 BTW... - Bernie (NoVA) 20:42:12 03/12/10
Post a Followup	You cannot reply to this message because you are not logged in.