Subject	Oxy-acetylene bishes!
Posted by	BobbyT on March 11, 2010 at 4:54 AM
	This message has been viewed 55 times.
In Reply To	why use a Dremel when you can use a grinder :) (n/m) posted by SuparexTT on March 11, 2010 at 02:48 AM
Message	Or thermite...?
Follow Ups	Victory is mine... - Eric(NJ) 21:47:34 03/10/10 (FL) (n/m) - Bernie (NoVA) 22:07:41 03/10/10 Exactly - ArubaDave 22:43:58 03/10/10 Wait, when did that happen?? (n/m) - TT XTZ 11:02:41 03/11/10 Left Jersey at ~9am 1/1/2009 got here at 3:30am 1/2/2009. (n/m) - Eric(NJ) 11:21:19 03/11/10 Very precise. ;-) (n/m) - TT XTZ 11:58:20 03/11/10 The correct answer is over 14 months ago - time to update - Bernie (NoVA) 23:18:34 03/11/10 Sweet - Insomniac (VA) 22:10:12 03/10/10 If I could go back I probably wouldn't do it without pulling - Eric(NJ) 22:17:45 03/10/10 Dump her dude... - FuerGrissa 22:10:18 03/10/10 Who is doing your powder coating? (n/m) - collegeboy 23:17:06 03/10/10 It's a local guy near me in Coral Springs. - Eric(NJ) 08:25:21 03/11/10 Welcome to the club :) - BradX (UF) 00:09:34 03/11/10 Re: Welcome to the club :) - -Grimm- 00:15:29 03/11/10 Yes, but the NOx are closer to the limit without it. - apudapus 00:35:22 03/11/10 Didn't see what the big deal was?!? - induetime 01:20:29 03/11/10 ditto. what a pain. (n/m) - SuparexTT 02:18:56 03/11/10 needs more dremel - LJZTT 02:47:25 03/11/10 why use a Dremel when you can use a grinder :) (n/m) - SuparexTT 02:48:54 03/11/10 dont take the easy way out...I couldnt find my hacksaw (n/m) - LJZTT 02:51:13 03/11/10 Oxy-acetylene bishes! - BobbyT 04:54:04 03/11/10 interesting, took the entire EGR system out of mine with - Cap927(Boston) 07:25:58 03/11/10 Trans in or out? If it was in I have no idea how you - Eric(NJ) 09:28:11 03/11/10 Carlos has small hands like the guy in the BK commercial. (n/m) - Dave N 09:42:52 03/11/10 trans in, battery out, plenum out, I was doing a plenum - Cap927(Boston) 11:10:06 03/11/10 What did you use to disconnect the EGR to manifold bung? - Eric(NJ) 11:19:28 03/11/10 DS DP was removed so I could get access to the manifold - Cap927(Boston) 11:47:10 03/11/10 OK, I did it the same way. Just didn't see a way to get a - Eric(NJ) 12:40:23 03/11/10 I gave it a shot before cutting pipes, if I had a tough time - Cap927(Boston) 12:53:01 03/11/10 You should mention...with the engine in :) (n/m) - ZiNnYc 06:52:09 03/11/10 Still not that tough. - zfreak(Dallas) 11:05:27 03/11/10 Mine was a PITA and I had mine on the engine stand. lol - KongZTT GT28RS MD 09:28:31 03/11/10 Nice. Congrats on getting that thing out. (n/m) - TT XTZ 11:03:42 03/11/10
Post a Followup	You cannot reply to this message because you are not logged in.