Subject	You are very correct.
Posted by	DVDBURN (MD) on November 03, 2009 at 12:34 PM
	This message has been viewed 107 times.
In Reply To	I agree and disagree with that : posted by Dark Diver on November 02, 2009 at 05:56 PM
Message	It's a very basic circuit and as you can see, only to be used for averaging. If the balance is significantly off there will be an upset in output. But then again, even with the Selin product or a SAFC you will get the same results in an unbalanced situation. Maybe not as much as in this basic circuit, but a difference non-the-less. It's best to have some sort of monitoring device to alert you either ahead of time or when you suspect something is wrong in an unbalance situation. This is why I feel a metering device such as a SAFC is very beneficial in a circuit (a dual MAF setup) like this. (Total Mouse Over Hits: a Lot) www.mytwinturbo.com Watch an ECZA meet caravan! Watch a DVDBURN video!
Follow Ups	Selin install. Thanks Jim! - Tu 18:33:49 11/01/09 Nice! - DVDBURN (MD) 19:21:29 11/01/09 One thing I might mention too is... - DVDBURN (MD) 20:42:49 11/01/09 Re: One thing I might mention too is... - BanzaiZX 03:38:40 11/02/09 Correct, my unit uses a processor in this way - CaliguyPurdue (Selin Design) 11:38:28 11/02/09 Yes, the ECU converts the analog MAF input signal... - DVDBURN (MD) 12:03:01 11/02/09 This is a circuit based on analog operational amplifier. - Dark Diver 08:29:06 11/02/09 Re: This is a circuit based on analog operational amplifier. - BanzaiZX 09:34:44 11/02/09 That's exactly what I said : - Dark Diver 17:25:12 11/02/09 This circuit is incorrect. Details inside... - CaliguyPurdue (Selin Design) 11:34:11 11/02/09 Here's a picture of the bare boards... - CaliguyPurdue (Selin Design) 12:36:53 11/02/09 very impressive sir. Was wondering what was on the inside. - Tu 12:53:09 11/02/09 Sorry. I didn't mean to imply that your design was inferior - DVDBURN (MD) 14:40:39 11/02/09 Bye bye JIM Wolf hello JIM Selin :-) - ArubaDave 21:11:53 11/02/09 I agree and disagree with that : - Dark Diver 17:56:57 11/02/09 You are very correct. - DVDBURN (MD) 12:34:25 11/03/09 ok.. for the Add or Average, whats what - JustinSCZ32 19:35:46 11/01/09 I would assume add is for normal ECUs - collegeboy 20:00:20 11/01/09 I think its the exact opposite. - J-Mart 08:40:43 11/02/09 I am WRONG! I better go check my SAFC settings... - J-Mart 08:52:57 11/02/09 yup (n/m) - ali300zx 08:48:01 11/02/09 I feel that AVE is better - Carlos Ramirez 20:04:47 11/01/09 Not sure about the Selin, but when using an SAFC, the ADD - zgene4 20:23:34 11/01/09 Re: I feel that AVE is better - BanzaiZX 04:12:04 11/02/09 6 of one, half dozen of the other, just depends on EPROM (n/m) - BigTDogg (MA) 10:06:23 11/02/09 ADD is for a "single pop ECU" but you'll encounter the 500HP - Dark Diver 18:00:04 11/02/09 Nice! (n/m) - Musashi Sword 19:44:26 11/01/09 did you install the centre T-bolts before installing the - vorpalZ 21:05:10 11/01/09 I had both filters off for the final fit. I like easy. (n/m) - Tu 12:41:31 11/02/09 Thanks Tu! Great pictures and post.. - CaliguyPurdue (Selin Design) 11:42:59 11/02/09
Post a Followup	You cannot reply to this message because you are not logged in.