Subject	I was in Fallon Nevada at top gun raceway on Saturday
Posted by	Machtavian on October 19, 2009 at 2:00 PM
	This message has been viewed 34 times.
In Reply To	Is that sac raceway? I was hoping to see you there last posted by ZEVAN (Ca) on October 19, 2009 at 01:48 PM
Message	I was going to come out later that night but I cut my finger very badly and had to go to the ER and get 8 stitches. Now I have all week off and I'm bored to tears no pun intended:)
Follow Ups	Tips for the dragstrip with slicks? - Ice95z 11:18:33 10/19/09 You have to find a medium between bogging and spinning - TTFairladyZ 12:21:21 10/19/09 How does the launch control cut fuel and spark? (n/m) - ZEVAN (Ca) 13:56:49 10/19/09 It should only be ignition not fuel; cutting fuel would - Machtavian 14:06:53 10/19/09 I think the link he posted says fuel and spark. Anyways, I - ZEVAN (Ca) 14:14:38 10/19/09 It's fuel and spark simultaneously - TTFairladyZ 15:40:53 10/19/09 TT diff should be fine, axle might break if you wheel hop (n/m) - ztunerz 12:25:24 10/19/09 Profile says NA rear end. (n/m) - Dream Z 12:33:45 10/19/09 well then - get ready for a wanted add for a na diff :) (n/m) - ztunerz 21:42:58 10/19/09 Slicks + NA rear + 1-pc AL Driveshafe = bad times? - BigTDogg (MA) 08:37:07 10/20/09 no (n/m) - JustinSCZ32 12:17:08 10/20/09 I mean bad times as in broken parts. I know if nothing - BigTDogg (MA) 14:03:08 10/20/09 From my experience, I would launch around - Machtavian 13:30:06 10/19/09 Re: From my experience, I would launch around - Ice95z 13:39:49 10/19/09 I was a ten psi on that run. - Machtavian 13:47:41 10/19/09 skinnies will not prevent that.... (n/m) - zxtuner161 16:30:10 10/19/09 They help steer it straight... (n/m) - Machtavian 17:33:40 10/19/09 no they don't... u can get just out of control with - zxtuner161 17:38:12 10/19/09 Those 26x11.50 et streets are bias ply (n/m) - nissanguyz32 18:48:30 10/19/09 He's right, they are bias ply. (n/m) - MeatMan - 604Z.ca - 20:52:00 10/19/09 You obviously have no idea that those are bias ply - Machtavian 19:21:13 10/19/09 not all skinnies are bias ply... mine are radials - zxtuner161 21:18:40 10/19/09 Re: not all skinnies are bias ply... mine are radials - Ice95z 08:15:19 10/20/09 bias ply you get a much softer sidewall, a "wrinkle wall" - zxtuner161 08:29:37 10/20/09 Re: bias ply you get a much softer sidewall, a "wrinkle wall" - Ice95z 08:48:22 10/20/09 Is that sac raceway? I was hoping to see you there last - ZEVAN (Ca) 13:48:29 10/19/09 I was in Fallon Nevada at top gun raceway on Saturday - Machtavian 14:00:56 10/19/09 Are you going anytime soon? I'd love to see your z run. I - ZEVAN (Ca) 14:08:49 10/19/09 Not sure, but ill let you know if/ when i go out. (n/m) - Machtavian 14:11:13 10/19/09 Re: Tips for the dragstrip with slicks? - cinpatico 16:38:05 10/19/09 I have a 1 piece ds. My boost controller is a old - Ice95z 17:35:34 10/19/09 How do you boost 8psi? Aren't your wastegates set higher? (n/m) - BigTDogg (MA) 08:44:56 10/20/09 Launch at 7000rpm and hold on... I had gotten 1.63 60ft (n/m) - dream Z (MD) 09:44:47 10/20/09
Post a Followup	You cannot reply to this message because you are not logged in.