Subject	You have to find a medium between bogging and spinning
Posted by	TTFairladyZ on October 19, 2009 at 12:21 PM
	This message has been viewed 105 times.
In Reply To	Tips for the dragstrip with slicks? posted by Ice95z on October 19, 2009 at 11:18 AM
Message	I was lucky to have great conditions at the track this past summer. Took my MT DR's down to 16psi, and launched at 5K rpms while dumping the clutch, no burnout. Way back when at Atco, I used to launch at 3,500 rpms with the DR's, and bog every single time while slipping the clutch. You might want to give this a try also: La-Z-Link My second favorite Z mod next to my MT tires. 1990 Nissan 300ZXTT Stage III+ 11.96 e.t. 1.61 60ft on original stock turbos
Follow Ups	Tips for the dragstrip with slicks? - Ice95z 11:18:33 10/19/09 You have to find a medium between bogging and spinning - TTFairladyZ 12:21:21 10/19/09 How does the launch control cut fuel and spark? (n/m) - ZEVAN (Ca) 13:56:49 10/19/09 It should only be ignition not fuel; cutting fuel would - Machtavian 14:06:53 10/19/09 I think the link he posted says fuel and spark. Anyways, I - ZEVAN (Ca) 14:14:38 10/19/09 It's fuel and spark simultaneously - TTFairladyZ 15:40:53 10/19/09 TT diff should be fine, axle might break if you wheel hop (n/m) - ztunerz 12:25:24 10/19/09 Profile says NA rear end. (n/m) - Dream Z 12:33:45 10/19/09 well then - get ready for a wanted add for a na diff :) (n/m) - ztunerz 21:42:58 10/19/09 Slicks + NA rear + 1-pc AL Driveshafe = bad times? - BigTDogg (MA) 08:37:07 10/20/09 no (n/m) - JustinSCZ32 12:17:08 10/20/09 I mean bad times as in broken parts. I know if nothing - BigTDogg (MA) 14:03:08 10/20/09 From my experience, I would launch around - Machtavian 13:30:06 10/19/09 Re: From my experience, I would launch around - Ice95z 13:39:49 10/19/09 I was a ten psi on that run. - Machtavian 13:47:41 10/19/09 skinnies will not prevent that.... (n/m) - zxtuner161 16:30:10 10/19/09 They help steer it straight... (n/m) - Machtavian 17:33:40 10/19/09 no they don't... u can get just out of control with - zxtuner161 17:38:12 10/19/09 Those 26x11.50 et streets are bias ply (n/m) - nissanguyz32 18:48:30 10/19/09 He's right, they are bias ply. (n/m) - MeatMan - 604Z.ca - 20:52:00 10/19/09 You obviously have no idea that those are bias ply - Machtavian 19:21:13 10/19/09 not all skinnies are bias ply... mine are radials - zxtuner161 21:18:40 10/19/09 Re: not all skinnies are bias ply... mine are radials - Ice95z 08:15:19 10/20/09 bias ply you get a much softer sidewall, a "wrinkle wall" - zxtuner161 08:29:37 10/20/09 Re: bias ply you get a much softer sidewall, a "wrinkle wall" - Ice95z 08:48:22 10/20/09 Is that sac raceway? I was hoping to see you there last - ZEVAN (Ca) 13:48:29 10/19/09 I was in Fallon Nevada at top gun raceway on Saturday - Machtavian 14:00:56 10/19/09 Are you going anytime soon? I'd love to see your z run. I - ZEVAN (Ca) 14:08:49 10/19/09 Not sure, but ill let you know if/ when i go out. (n/m) - Machtavian 14:11:13 10/19/09 Re: Tips for the dragstrip with slicks? - cinpatico 16:38:05 10/19/09 I have a 1 piece ds. My boost controller is a old - Ice95z 17:35:34 10/19/09 How do you boost 8psi? Aren't your wastegates set higher? (n/m) - BigTDogg (MA) 08:44:56 10/20/09 Launch at 7000rpm and hold on... I had gotten 1.63 60ft (n/m) - dream Z (MD) 09:44:47 10/20/09
Post a Followup	You cannot reply to this message because you are not logged in.