Subject	if you take them apart >>>
Posted by	ztunerz on October 09, 2009 at 2:03 AM
	This message has been viewed 124 times.
In Reply To	are they available separately? (n/m) posted by Bernie (NoVA) on October 09, 2009 at 12:32 AM
Message	there two individual units in parallel. I'd assume one could split them up and use one for each turbo. I would be a bit worried running 4 solonoids (2 units) with one controller. Obviously it works but maybe it would have a negative effect over time on the control unit itself given the additional load. Harry Formerly yellowzxtt
Follow Ups	Why is the boost control pressure source supposed to be t'd? - Antihero 15:06:17 10/08/09 You can cap one side. (n/m) - MAD_96TT(ATX) 15:27:12 10/08/09 I think the thought is to T them for as accurate a pressure - treese88 15:27:25 10/08/09 the pressure source doesnt have to be accurate. - Antihero 15:50:49 10/08/09 I'm running dual solenoids with my Blitz EBC - zgene4 15:44:50 10/08/09 I can definitely see the benefit of the dual solenoid setup (n/m) - Antihero 15:51:38 10/08/09 Which solenoids are you using? (n/m) - Bernie (NoVA) 16:20:05 10/08/09 two of the blitz "dual" solenoids (n/m) - zgene4 19:52:02 10/08/09 are they available separately? (n/m) - Bernie (NoVA) 00:32:17 10/09/09 if you take them apart >>> - ztunerz 02:03:34 10/09/09 I found the second one in a parts car and purchased it for - zgene4 11:05:02 10/09/09 A little overkill :) (n/m) - ztunerz 20:52:12 10/08/09 Only because there is beauty in symmetry. (n/m) - chicagozer 16:46:25 10/08/09 2nd (n/m) - Fake_Blood 16:56:25 10/08/09 bad reason to throw extra crap in the engine bay - Antihero 17:05:49 10/08/09 Re: bad reason to throw extra crap in the engine bay - Fake_Blood 17:18:24 10/08/09 please explain the actual benefit or the possible proble (n/m) - Antihero 17:55:00 10/08/09 Aslong as the output lines to the actuators are the same - boileralum 18:29:36 10/08/09 Why should the tubing length matter? - fldc 18:41:14 10/08/09 B/c the solenoid is going to show 0 pressure to the line - boileralum 18:58:48 10/08/09 I've alway thought that you can't adjust the wastegate - not4resaleZ 21:28:31 10/08/09 extremely poor comparison - ZLover4Life 23:36:35 10/08/09 It was kind of a joke. Obviously electricity travels - not4resaleZ 17:39:39 10/09/09 balanced wastegate response (n/m) - Bernie (NoVA) 00:45:46 10/09/09 Alot of opinion but how many people are using just one line? - LivinTheDream 21:06:26 10/08/09 For a pressure source to activate your solenoids, - not4resaleZ 17:52:11 10/09/09 Pressure sensor readings will be more accurate... - DEVILS Z-Tech (CA) 22:53:44 10/08/09 we are not talking about the pressure sensor signal - Antihero 08:59:43 10/09/09 Have there been comparisons from a controller running "T'd"? - JustinSCZ32 15:40:27 10/09/09
Post a Followup	You cannot reply to this message because you are not logged in.