Subject	I think the thought is to T them for as accurate a pressure
Posted by	treese88 on October 08, 2009 at 3:27 PM
	This message has been viewed 104 times.
In Reply To	Why is the boost control pressure source supposed to be t'd? posted by Antihero on October 08, 2009 at 03:06 PM
Message	source as possible. I've never felt this has much of a real gain though. It would be nice to lose one of the lines and save some plumbing. Hope to see some good discussion. '91 TT
Follow Ups	Why is the boost control pressure source supposed to be t'd? - Antihero 15:06:17 10/08/09 You can cap one side. (n/m) - MAD_96TT(ATX) 15:27:12 10/08/09 I think the thought is to T them for as accurate a pressure - treese88 15:27:25 10/08/09 the pressure source doesnt have to be accurate. - Antihero 15:50:49 10/08/09 I'm running dual solenoids with my Blitz EBC - zgene4 15:44:50 10/08/09 I can definitely see the benefit of the dual solenoid setup (n/m) - Antihero 15:51:38 10/08/09 Which solenoids are you using? (n/m) - Bernie (NoVA) 16:20:05 10/08/09 two of the blitz "dual" solenoids (n/m) - zgene4 19:52:02 10/08/09 are they available separately? (n/m) - Bernie (NoVA) 00:32:17 10/09/09 if you take them apart >>> - ztunerz 02:03:34 10/09/09 I found the second one in a parts car and purchased it for - zgene4 11:05:02 10/09/09 A little overkill :) (n/m) - ztunerz 20:52:12 10/08/09 Only because there is beauty in symmetry. (n/m) - chicagozer 16:46:25 10/08/09 2nd (n/m) - Fake_Blood 16:56:25 10/08/09 bad reason to throw extra crap in the engine bay - Antihero 17:05:49 10/08/09 Re: bad reason to throw extra crap in the engine bay - Fake_Blood 17:18:24 10/08/09 please explain the actual benefit or the possible proble (n/m) - Antihero 17:55:00 10/08/09 Aslong as the output lines to the actuators are the same - boileralum 18:29:36 10/08/09 Why should the tubing length matter? - fldc 18:41:14 10/08/09 B/c the solenoid is going to show 0 pressure to the line - boileralum 18:58:48 10/08/09 I've alway thought that you can't adjust the wastegate - not4resaleZ 21:28:31 10/08/09 extremely poor comparison - ZLover4Life 23:36:35 10/08/09 It was kind of a joke. Obviously electricity travels - not4resaleZ 17:39:39 10/09/09 balanced wastegate response (n/m) - Bernie (NoVA) 00:45:46 10/09/09 Alot of opinion but how many people are using just one line? - LivinTheDream 21:06:26 10/08/09 For a pressure source to activate your solenoids, - not4resaleZ 17:52:11 10/09/09 Pressure sensor readings will be more accurate... - DEVILS Z-Tech (CA) 22:53:44 10/08/09 we are not talking about the pressure sensor signal - Antihero 08:59:43 10/09/09 Have there been comparisons from a controller running "T'd"? - JustinSCZ32 15:40:27 10/09/09
Post a Followup	You cannot reply to this message because you are not logged in.