Subject	Great way to bolt the filters in place.
Posted by	collegeboy on September 23, 2009 at 10:35 AM
	This message has been viewed 244 times.
In Reply To	Selin DUAL MAF Hardware Kit fitment with Nismo Oil cooler posted by Bernie (NoVA) on September 23, 2009 at 02:24 AM
Message	I don't like them being that close to the oil cooler though, even with brackets, things can still move a little, but hopefully not enough to cause any rub-through. Thanks, Mike 1991 Black 3.0 Twin Turbo La-Z-Link ^^Hard engine break in method^^ La-Z-Link ^^MY FACEBOOK...CHECK IT OUT^^ ---Me: You bought a Porsche? ---sfpearl300z: lol, no no, I have a decent sized penis so no need for that. "felt wierd fingering my exhuast for 1hr with no results :(" - zboost "lmao, i know, theres more drama and favoritism on tt.net than a middle school girls locker room" - sfpearl300z "I think I'll pass on giving my car a handjob" - joel(PA) "I did plug the holes, But I did it by taping over them a lot, I didnt think that maybe HOT air is comming through there, And it melted the tape, damnit im an ass." - DC 21
Follow Ups	Selin DUAL MAF Hardware Kit fitment with Nismo Oil cooler - Bernie (NoVA) 02:24:36 09/23/09 What is the cost of the kit you have? (n/m) - toykoz32 02:39:40 09/23/09 ?... - Halo Z 07:11:02 09/23/09 Bernies Z: Spotless inside and out (n/m) - Broke_as_**** 02:47:05 09/23/09 Clean.. (n/m) - TTZ'in (NorCal) 02:59:03 09/23/09 Nice to see you working on your own Z for a change (n/m) - BlackTT91 03:44:49 09/23/09 Nice! (n/m) - DVDBURN (MD) 05:19:33 09/23/09 Nice job Bernie. I noticed that even with a single POP - Cap927(Boston) 07:49:46 09/23/09 Nice work Bernie! (n/m) - Piranha(PHX) 08:37:53 09/23/09 yeah, that's what i did on the brackets - RedSER13 10:03:42 09/23/09 looks great.. cmon Bernie you know you cleaned before you - fst300zx 10:32:10 09/23/09 Great way to bolt the filters in place. - collegeboy 10:35:13 09/23/09 Very nice. Did you use the oil restrictor w/the NISMO OC? (n/m) - Scotts94z32 11:26:57 09/23/09 I used the hoses/lines which where included w. the kit. (n/m) - Bernie (NoVA) 11:35:45 09/23/09 Location of filters behind splash shields. - enthuZiast 12:03:34 09/23/09 Yes. (n/m) - Bernie (NoVA) 12:04:22 09/23/09 YOU have bov's? (n/m) - 91Z32TT 12:24:10 09/23/09 Since '02. (n/m) - Bernie (NoVA) 12:52:28 09/23/09 old school ninja (n/m) - Drk93TT 13:12:55 09/23/09 You have the recirc fittings? (n/m) - BigTDogg (MA) 20:02:52 09/23/09 doesn't look like he does... (n/m) - kenecchi 09:29:30 09/24/09 <<------- Classifieds. (n/m) - Jackie 12:40:50 09/23/09 Buy a Z ---------->> (n/m) - Bernie (NoVA) 12:51:16 09/23/09 You Selin one? (n/m) - Jackie 17:56:20 09/23/09 Yes. - Bernie (NoVA) 11:23:22 09/24/09 Ha! You actually are. Looks clean. (n/m) - Jackie 12:49:51 09/24/09 Clean set up (n/m) - RobZ32 13:23:27 09/23/09 Does look good! (n/m) - SeedyROM 13:53:18 09/23/09 Why the Jim Wolf stickers on the MAF's? - pieboy100 14:12:09 09/23/09 for the JWT filters attached to them... (n/m) - Halo Z 14:18:02 09/23/09 it adds weight (n/m) - SuparexTT 14:32:06 09/23/09 Is a low speed driveabilty hose connection required? (n/m) - pieboy100 20:05:02 09/23/09 No - thats half the reason to run Dual MAF (n/m) - Bernie (NoVA) 20:55:14 09/23/09 So.... about 500 dollars for a new MAF? (n/m) - pieboy100 20:03:50 09/23/09 or ~$100 for a used on. (n/m) - Bernie (NoVA) 20:55:39 09/23/09 Very nice settup. (n/m) - dregos 15:37:12 09/23/09 Nice. I had to move my earls cooler back and remove - ShakaShaun(Denver) 18:19:59 09/23/09 You're doing something wrong then. Never removed any AUX - Bernie (NoVA) 20:56:34 09/23/09 I agree with Bernie, I didn't have to move my stillen cooler - DavezTT 23:37:28 09/23/09 To clarify, are you refering to my kit or another? (n/m) - CaliguyPurdue (Selin Design) 15:25:24 09/24/09
Post a Followup	You cannot reply to this message because you are not logged in.