Subject	Re: Wow, I never knew you guys were developing such a monster
Posted by	Russell@Z1 on August 20, 2009 at 10:57 AM
	This message has been viewed 97 times.
In Reply To	Wow, I never knew you guys were developing such a monster posted by Machtavian on August 20, 2009 at 10:49 AM
Message	That is a legitimate concern. We took several junk bare blocks and drilled them out considerably further to see where the limits were and concluded that there is enough "meat". For additional testing we've also put over 200 ft-lbs of torque on some studs in some of the holes in the junk test blocks we drilled to make sure they would hold. Russell Floyd Z1 Motorsports www.300zx.com 1990+ Nissan Z specialists Used Parts, New parts, Service/Repair and Performance Z1 Motorsports Exclusive Parts Line 2877 Carrollton Villa Rica Hwy Carrollton, Ga 30116 770-838-7777 770-832-9253 (fax)
Follow Ups	Gauging interest in ARP L19 head studs - Machtavian 08:55:34 08/20/09 Try asking at 300zxclub.com too, since there are many - TheTwinZ (Peru) 09:15:28 08/20/09 Re: Try asking at 300zxclub.com too, since there are many - nissansx 09:56:25 08/20/09 $1200 for head studs??? They must be platinum. LOL - phillyz 09:57:49 08/20/09 Lol - Machtavian 10:11:11 08/20/09 Re: Lol - Russell@Z1 10:38:47 08/20/09 holy crap - nissansx 10:42:29 08/20/09 Wow, I never knew you guys were developing such a monster - Machtavian 10:49:12 08/20/09 Re: Wow, I never knew you guys were developing such a monster - Russell@Z1 10:57:05 08/20/09 What's the turn around time for the machining? (n/m) - Machtavian 11:06:57 08/20/09 Re: What's the turn around time for the machining? - Russell@Z1 11:37:24 08/20/09 What are the "several obvious reasons"? - BobbyT 15:08:54 08/20/09 Re: What are the "several obvious reasons"? - ZLover4Life 18:05:25 08/20/09 that, and 230 ft-lbs would probably cause significant - aliaZ 22:15:06 08/20/09 I'm currently getting quotes for head and main studs - LitlElvis 10:01:49 08/20/09 Yes the two short one too. (n/m) - Machtavian 10:06:03 08/20/09 That one has to be driving up the cost a bunch due to the - LitlElvis 10:13:17 08/20/09 Exactly (n/m) - Machtavian 10:24:08 08/20/09 If you happen across anything in the next few months - 91Z32TT 11:39:14 08/20/09 Re: Gauging interest in ARP L19 head studs - WazTTed 10:10:59 08/20/09 The L19's are made of a lot stronger material then the - Machtavian 10:18:04 08/20/09 Since when have you seen regular ARP head studs fail ... - NytWolf 10:34:04 08/20/09 Numerous times. The heads will lift under high HP loads. (n/m) - bryan@Z1 10:35:50 08/20/09 It's not about outright failure, it's about adding more - LitlElvis 10:37:07 08/20/09 We've looked into this as well.... - bryan@Z1 10:11:51 08/20/09 When do you guys expect to stock them? (n/m) - Machtavian 10:24:58 08/20/09 Re: When do you guys expect to stock them? - bryan@Z1 10:30:30 08/20/09 Re: Gauging interest in ARP L19 head studs - Tech@EPR 10:35:38 08/20/09 That is awesome, how many people do you currently have? (n/m) - Machtavian 10:41:06 08/20/09 2nd, I am definitely in. - 91Z32TT 11:18:34 08/20/09
Post a Followup	You cannot reply to this message because you are not logged in.