Subject	This is why I did it like I did, and it's why MWS does
Posted by	BigTDogg (MA) on June 10, 2009 at 1:48 PM
	This message has been viewed 60 times.
In Reply To	Which is what you want. The boost pressure going into posted by not4resaleZ on June 10, 2009 at 07:55 AM
Message	It like I said: That's directly from the EVC5 install manual, I just added the colors to coordinate with the picture of my install below: The silver reads manifold pressure, the red reads compressor outlet pressure. Will it work if he runs the red line off the balance tube? Of course, but the way shown above is optimal. "...Downpipes own. They own everything...anything...all there ever was and will be...they should be stock on all cars. Screw the environment, emissions, noise! I love them...I shall name my first-born after them with glee..." - SeedyRom 05:13:20 10/03/02 "i love the cock" - genic 22:20:47 09/25/03 "I hope you get fucked in the ass with a pringles can." - ni[X]it 14:53:53 02/02/06 "Either ignore him or beat him up. Anything else will be over his head." - Marshall 12:28:23 08/18/04 "Ok, Ill bite.." eriksu9 15:42:10 04/04/08 z32baby: yeah, my memory sucks balls DJ Juiced: What's your memory doing this friday night? ;) "i've got to the point where i can drive the Z at its limits and i want more" - shadowZ 16:29:56 08/31/04 "I was way more timid then than I am now about getting in there and yanking on things." - TT XTZ 13:30:34 07/25/05 "Just ran out to get some knee pads. I'm ready now... BRING.....IT.....ON... :-) " - Dave N 19:04:30 10/31/07
Follow Ups	Anbody use the balance tube vacuum port left over from - ConVerTT 16:03:40 06/07/09 The EBC solenoid should get its pressure feed - pcproa 16:27:28 06/07/09 You need a dependable source of pressurized air. (n/m) - not4resaleZ 17:16:15 06/07/09 Dark River answered my question in Tech - mods pls delete (n/m) - ConVerTT 18:45:21 06/07/09 Sure it will work, but you are not effectively - pcproa 19:08:02 06/07/09 I do see your point - ConVerTT 19:22:14 06/07/09 I think pcproa is still pulling the boost presure - not4resaleZ 19:41:18 06/07/09 Now i understand your earlier post - ConVerTT 19:58:05 06/07/09 Yes, and the pressure is there when you need it. (n/m) - not4resaleZ 20:08:26 06/07/09 Exactly, when you close the throttle plates - pcproa 20:09:54 06/07/09 OK - but that isn't that what the recirculation valves are - ConVerTT 20:26:29 06/07/09 Recircs recycle as much of the air as they can - pcproa 20:29:56 06/07/09 Good point. - ConVerTT 22:46:52 06/08/09 And it doesn't need pressure, if the manifold has none. (n/m) - not4resaleZ 20:55:13 06/07/09 Pulling the boost pressure to send to the controller - pcproa 20:06:41 06/07/09 Prolly not a good spot. (n/m) - collegeboy 21:07:42 06/07/09 It's good for a boost gauge or some other manifild sensor - BigTDogg (MA) 07:43:19 06/08/09 Why as close to the compressor outlet as possible? - not4resaleZ 09:46:56 06/08/09 Pressure loss through the system, see pcproa's post (n/m) - BigTDogg (MA) 22:34:46 06/08/09 Pressure loss?? You have enough pressure to need a - not4resaleZ 16:15:06 06/09/09 Opening the wastegates isn't the issue, it's knowing when to - BigTDogg (MA) 21:25:49 06/09/09 Which is what you want. The boost pressure going into - not4resaleZ 07:55:38 06/10/09 This is why I did it like I did, and it's why MWS does - BigTDogg (MA) 13:48:05 06/10/09 Very nice car. I really prefer taking the pressure - not4resaleZ 16:39:14 06/10/09 LOL, no problem, and thanks for the compliments on the car - BigTDogg (MA) 07:27:13 06/11/09 Hey 'Dogg - ConVerTT 22:45:25 06/08/09 No prob, gotta get rid of this stuff :-) - BigTDogg (MA) 09:14:51 06/09/09
Post a Followup	You cannot reply to this message because you are not logged in.