Subject	Which is what you want. The boost pressure going into
Posted by	not4resaleZ on June 10, 2009 at 7:55 AM
	This message has been viewed 51 times.
In Reply To	Opening the wastegates isn't the issue, it's knowing when to posted by BigTDogg (MA) on June 09, 2009 at 09:25 PM
Message	your engine is what is critical to control (and measure) to prevent detonation, so you measure it at the manifold with the sensor that goes to the EBC. Every post I have seen uses a balance tube location to measure the amount of boost. The source of the power to move the wastegate actuator is the question.
Follow Ups	Anbody use the balance tube vacuum port left over from - ConVerTT 16:03:40 06/07/09 The EBC solenoid should get its pressure feed - pcproa 16:27:28 06/07/09 You need a dependable source of pressurized air. (n/m) - not4resaleZ 17:16:15 06/07/09 Dark River answered my question in Tech - mods pls delete (n/m) - ConVerTT 18:45:21 06/07/09 Sure it will work, but you are not effectively - pcproa 19:08:02 06/07/09 I do see your point - ConVerTT 19:22:14 06/07/09 I think pcproa is still pulling the boost presure - not4resaleZ 19:41:18 06/07/09 Now i understand your earlier post - ConVerTT 19:58:05 06/07/09 Yes, and the pressure is there when you need it. (n/m) - not4resaleZ 20:08:26 06/07/09 Exactly, when you close the throttle plates - pcproa 20:09:54 06/07/09 OK - but that isn't that what the recirculation valves are - ConVerTT 20:26:29 06/07/09 Recircs recycle as much of the air as they can - pcproa 20:29:56 06/07/09 Good point. - ConVerTT 22:46:52 06/08/09 And it doesn't need pressure, if the manifold has none. (n/m) - not4resaleZ 20:55:13 06/07/09 Pulling the boost pressure to send to the controller - pcproa 20:06:41 06/07/09 Prolly not a good spot. (n/m) - collegeboy 21:07:42 06/07/09 It's good for a boost gauge or some other manifild sensor - BigTDogg (MA) 07:43:19 06/08/09 Why as close to the compressor outlet as possible? - not4resaleZ 09:46:56 06/08/09 Pressure loss through the system, see pcproa's post (n/m) - BigTDogg (MA) 22:34:46 06/08/09 Pressure loss?? You have enough pressure to need a - not4resaleZ 16:15:06 06/09/09 Opening the wastegates isn't the issue, it's knowing when to - BigTDogg (MA) 21:25:49 06/09/09 Which is what you want. The boost pressure going into - not4resaleZ 07:55:38 06/10/09 This is why I did it like I did, and it's why MWS does - BigTDogg (MA) 13:48:05 06/10/09 Very nice car. I really prefer taking the pressure - not4resaleZ 16:39:14 06/10/09 LOL, no problem, and thanks for the compliments on the car - BigTDogg (MA) 07:27:13 06/11/09 Hey 'Dogg - ConVerTT 22:45:25 06/08/09 No prob, gotta get rid of this stuff :-) - BigTDogg (MA) 09:14:51 06/09/09
Post a Followup	You cannot reply to this message because you are not logged in.