Subject	Hey 'Dogg
Posted by	ConVerTT on June 08, 2009 at 10:45 PM
	This message has been viewed 40 times.
In Reply To	It's good for a boost gauge or some other manifild sensor posted by BigTDogg (MA) on June 08, 2009 at 07:43 AM
Message	After thinking about it overnight and staring at the engine and the engine bay, I think that you and pcproa are correct. I am going to tap close to the compressor outlets. I already have a spare set of pipes - thanks for offerring.
Follow Ups	Anbody use the balance tube vacuum port left over from - ConVerTT 16:03:40 06/07/09 The EBC solenoid should get its pressure feed - pcproa 16:27:28 06/07/09 You need a dependable source of pressurized air. (n/m) - not4resaleZ 17:16:15 06/07/09 Dark River answered my question in Tech - mods pls delete (n/m) - ConVerTT 18:45:21 06/07/09 Sure it will work, but you are not effectively - pcproa 19:08:02 06/07/09 I do see your point - ConVerTT 19:22:14 06/07/09 I think pcproa is still pulling the boost presure - not4resaleZ 19:41:18 06/07/09 Now i understand your earlier post - ConVerTT 19:58:05 06/07/09 Yes, and the pressure is there when you need it. (n/m) - not4resaleZ 20:08:26 06/07/09 Exactly, when you close the throttle plates - pcproa 20:09:54 06/07/09 OK - but that isn't that what the recirculation valves are - ConVerTT 20:26:29 06/07/09 Recircs recycle as much of the air as they can - pcproa 20:29:56 06/07/09 Good point. - ConVerTT 22:46:52 06/08/09 And it doesn't need pressure, if the manifold has none. (n/m) - not4resaleZ 20:55:13 06/07/09 Pulling the boost pressure to send to the controller - pcproa 20:06:41 06/07/09 Prolly not a good spot. (n/m) - collegeboy 21:07:42 06/07/09 It's good for a boost gauge or some other manifild sensor - BigTDogg (MA) 07:43:19 06/08/09 Why as close to the compressor outlet as possible? - not4resaleZ 09:46:56 06/08/09 Pressure loss through the system, see pcproa's post (n/m) - BigTDogg (MA) 22:34:46 06/08/09 Pressure loss?? You have enough pressure to need a - not4resaleZ 16:15:06 06/09/09 Opening the wastegates isn't the issue, it's knowing when to - BigTDogg (MA) 21:25:49 06/09/09 Which is what you want. The boost pressure going into - not4resaleZ 07:55:38 06/10/09 This is why I did it like I did, and it's why MWS does - BigTDogg (MA) 13:48:05 06/10/09 Very nice car. I really prefer taking the pressure - not4resaleZ 16:39:14 06/10/09 LOL, no problem, and thanks for the compliments on the car - BigTDogg (MA) 07:27:13 06/11/09 Hey 'Dogg - ConVerTT 22:45:25 06/08/09 No prob, gotta get rid of this stuff :-) - BigTDogg (MA) 09:14:51 06/09/09
Post a Followup	You cannot reply to this message because you are not logged in.