Subject	The EBC solenoid should get its pressure feed
Posted by	pcproa on June 07, 2009 at 4:27 PM
	This message has been viewed 109 times.
In Reply To	Anbody use the balance tube vacuum port left over from posted by ConVerTT on June 07, 2009 at 04:03 PM
Message	from right after the compressor outlet, thus creating the best response time. Putting it all the way up on the balance tube significantly reduces response time and does not do much to relieving the boost pressure when the throttle flaps are closed. If you would like to use that port, use it for the input to your Boost Sensor on your EBC instead. That will give your Controller a close to accurate reading of the boost pressure that your cylinders are seeing. Popformance - Automotive Performance Electronics http://www.popformance.com 1990 Nissan 300ZX 1982 Datsun 200SX Cardomain website
Follow Ups	Anbody use the balance tube vacuum port left over from - ConVerTT 16:03:40 06/07/09 The EBC solenoid should get its pressure feed - pcproa 16:27:28 06/07/09 You need a dependable source of pressurized air. (n/m) - not4resaleZ 17:16:15 06/07/09 Dark River answered my question in Tech - mods pls delete (n/m) - ConVerTT 18:45:21 06/07/09 Sure it will work, but you are not effectively - pcproa 19:08:02 06/07/09 I do see your point - ConVerTT 19:22:14 06/07/09 I think pcproa is still pulling the boost presure - not4resaleZ 19:41:18 06/07/09 Now i understand your earlier post - ConVerTT 19:58:05 06/07/09 Yes, and the pressure is there when you need it. (n/m) - not4resaleZ 20:08:26 06/07/09 Exactly, when you close the throttle plates - pcproa 20:09:54 06/07/09 OK - but that isn't that what the recirculation valves are - ConVerTT 20:26:29 06/07/09 Recircs recycle as much of the air as they can - pcproa 20:29:56 06/07/09 Good point. - ConVerTT 22:46:52 06/08/09 And it doesn't need pressure, if the manifold has none. (n/m) - not4resaleZ 20:55:13 06/07/09 Pulling the boost pressure to send to the controller - pcproa 20:06:41 06/07/09 Prolly not a good spot. (n/m) - collegeboy 21:07:42 06/07/09 It's good for a boost gauge or some other manifild sensor - BigTDogg (MA) 07:43:19 06/08/09 Why as close to the compressor outlet as possible? - not4resaleZ 09:46:56 06/08/09 Pressure loss through the system, see pcproa's post (n/m) - BigTDogg (MA) 22:34:46 06/08/09 Pressure loss?? You have enough pressure to need a - not4resaleZ 16:15:06 06/09/09 Opening the wastegates isn't the issue, it's knowing when to - BigTDogg (MA) 21:25:49 06/09/09 Which is what you want. The boost pressure going into - not4resaleZ 07:55:38 06/10/09 This is why I did it like I did, and it's why MWS does - BigTDogg (MA) 13:48:05 06/10/09 Very nice car. I really prefer taking the pressure - not4resaleZ 16:39:14 06/10/09 LOL, no problem, and thanks for the compliments on the car - BigTDogg (MA) 07:27:13 06/11/09 Hey 'Dogg - ConVerTT 22:45:25 06/08/09 No prob, gotta get rid of this stuff :-) - BigTDogg (MA) 09:14:51 06/09/09
Post a Followup	You cannot reply to this message because you are not logged in.