Subject	Do it yourself
Posted by	collegeboy on June 04, 2009 at 9:56 PM
	This message has been viewed 86 times.
In Reply To	Z1 quoted me a minimum of $85 to tap EGTs in posted by yobobrox on June 04, 2009 at 08:56 PM
Message	Seriously, it's very easy. If you have a drill already then you can easily do it and save the money. If you are unsure what threads they are, then just look it up online if it was not provided with the gauge. Then drill, and tap. It's hard to mess up. Have fun! Thanks, Mike 1991 Black 3.0 Twin Turbo La-Z-Link ^^Hard engine break in method^^ La-Z-Link ^^MY FACEBOOK...CHECK IT OUT^^ ---Me: You bought a Porsche? ---sfpearl300z: lol, no no, I have a decent sized penis so no need for that. "felt wierd fingering my exhuast for 1hr with no results :(" - zboost "lmao, i know, theres more drama and favoritism on tt.net than a middle school girls locker room" - sfpearl300z "I think I'll pass on giving my car a handjob" - joel(PA) "I did plug the holes, But I did it by taping over them a lot, I didnt think that maybe HOT air is comming through there, And it melted the tape, damnit im an ass." - DC 21
Follow Ups	Z1 quoted me a minimum of $85 to tap EGTs in - yobobrox 20:56:49 06/04/09 Specialty Z tapped my MSP manifolds for dual EGT probes - zgene4 21:01:02 06/04/09 Do you have any pics that you can share? - 1blackz 22:23:06 06/04/09 Yes, right before the turbo. Here's a few pics: - zgene4 23:16:02 06/04/09 that is well done. (n/m) - spotz 23:23:07 06/04/09 Thanks, it would be nice of they read temps greater than 0 - zgene4 23:35:14 06/04/09 What kind of sensors/gauges are you using? (n/m) - yobobrox 09:32:31 06/05/09 My EGT gauges are STRI (n/m) - zgene4 17:00:49 06/05/09 What do you mean? (n/m) - Scotts94z32 10:26:12 06/05/09 still bench racing indoors... - zgene4 11:45:09 06/05/09 Nice! (n/m) - 1blackz 03:52:13 06/05/09 Re: Do you have any pics that you can share? - Z300Z 05:19:20 06/05/09 they're easy enough to DIY - aliaZ 21:01:25 06/04/09 I'm mainly concerned about two things: - yobobrox 21:04:43 06/04/09 for starters, these are useful - gt300zxtt 21:21:34 06/04/09 Most EGT probes I've seen are 1/8" NPT, but the specs - zgene4 21:24:03 06/04/09 Do it yourself - collegeboy 21:56:05 06/04/09 I just tapped my own last night - Spectrum (WI) 23:20:11 06/04/09 Do you have the MSP's as well? Looking at zgene4's: - yobobrox 09:36:13 06/05/09 Zgene's are in the flat spot. - Woody75 (Denver) 10:12:55 06/05/09 Gotcha - thnx, I'll go look at mine again. (n/m) - yobobrox 10:40:49 06/05/09 pay the price or find somewhere cheaper. - SuparexTT 09:59:25 06/05/09 ? I wasn't comparing anyone. I just think that $85 is - yobobrox 10:42:24 06/05/09 Re: Z1 quoted me a minimum of $85 to tap EGTs in - WazTTed 11:20:03 06/05/09 ygm (n/m) - John@Z1 12:22:10 06/05/09 DIY - But use a lot of lube when tapping Mike Smith - ConVerTT 14:11:43 06/05/09 PS >>> mine were 1/8 NPT 27 tap, 11/32 bit (n/m) - ConVerTT 14:21:10 06/05/09 "use a lot of lube when tapping Mike Smith" - Z_Cherub 14:25:31 06/05/09 Lol, wow. (n/m) - ImTheDevil 15:42:21 06/05/09 bwahahahaha... nice (n/m) - vorpalZ 20:38:51 06/05/09 Oh snap! (n/m) - BradZ (UF) 15:58:04 06/05/09 call me stupid, i'm missing something. - SuparexTT 16:15:07 06/05/09 His tap handle broke (n/m) - zgene4 17:02:45 06/05/09 Correct - manis are fine (n/m) - ConVerTT 18:40:17 06/05/09 um (n/m) - ZiNnYc 17:29:32 06/05/09 Awesome - thnx for the humor and the pix! :B - yobobrox 19:01:50 06/05/09 test it on some AMS units ;) (n/m) - SuparexTT 19:16:01 06/05/09 Take it to a machine shop or call around. About 20 min of - AZHeat 16:11:52 06/06/09 Thnx, useful info (n/m) - yobobrox 00:28:46 06/07/09
Post a Followup	You cannot reply to this message because you are not logged in.