Subject	I'm mainly concerned about two things:
Posted by	yobobrox on June 04, 2009 at 9:04 PM
	This message has been viewed 114 times.
In Reply To	they're easy enough to DIY posted by aliaZ on June 04, 2009 at 09:01 PM
Message	1. I don't have a drill press and I'm worried about drilling a pilot hole crooked. 2. I'm not very familiar with thread definitions. I have my EGTs and I'm sure I can determine the size, but I'd be uncertain if I chose the right kind of tap. Any advice?
Follow Ups	Z1 quoted me a minimum of $85 to tap EGTs in - yobobrox 20:56:49 06/04/09 Specialty Z tapped my MSP manifolds for dual EGT probes - zgene4 21:01:02 06/04/09 Do you have any pics that you can share? - 1blackz 22:23:06 06/04/09 Yes, right before the turbo. Here's a few pics: - zgene4 23:16:02 06/04/09 that is well done. (n/m) - spotz 23:23:07 06/04/09 Thanks, it would be nice of they read temps greater than 0 - zgene4 23:35:14 06/04/09 What kind of sensors/gauges are you using? (n/m) - yobobrox 09:32:31 06/05/09 My EGT gauges are STRI (n/m) - zgene4 17:00:49 06/05/09 What do you mean? (n/m) - Scotts94z32 10:26:12 06/05/09 still bench racing indoors... - zgene4 11:45:09 06/05/09 Nice! (n/m) - 1blackz 03:52:13 06/05/09 Re: Do you have any pics that you can share? - Z300Z 05:19:20 06/05/09 they're easy enough to DIY - aliaZ 21:01:25 06/04/09 I'm mainly concerned about two things: - yobobrox 21:04:43 06/04/09 for starters, these are useful - gt300zxtt 21:21:34 06/04/09 Most EGT probes I've seen are 1/8" NPT, but the specs - zgene4 21:24:03 06/04/09 Do it yourself - collegeboy 21:56:05 06/04/09 I just tapped my own last night - Spectrum (WI) 23:20:11 06/04/09 Do you have the MSP's as well? Looking at zgene4's: - yobobrox 09:36:13 06/05/09 Zgene's are in the flat spot. - Woody75 (Denver) 10:12:55 06/05/09 Gotcha - thnx, I'll go look at mine again. (n/m) - yobobrox 10:40:49 06/05/09 pay the price or find somewhere cheaper. - SuparexTT 09:59:25 06/05/09 ? I wasn't comparing anyone. I just think that $85 is - yobobrox 10:42:24 06/05/09 Re: Z1 quoted me a minimum of $85 to tap EGTs in - WazTTed 11:20:03 06/05/09 ygm (n/m) - John@Z1 12:22:10 06/05/09 DIY - But use a lot of lube when tapping Mike Smith - ConVerTT 14:11:43 06/05/09 PS >>> mine were 1/8 NPT 27 tap, 11/32 bit (n/m) - ConVerTT 14:21:10 06/05/09 "use a lot of lube when tapping Mike Smith" - Z_Cherub 14:25:31 06/05/09 Lol, wow. (n/m) - ImTheDevil 15:42:21 06/05/09 bwahahahaha... nice (n/m) - vorpalZ 20:38:51 06/05/09 Oh snap! (n/m) - BradZ (UF) 15:58:04 06/05/09 call me stupid, i'm missing something. - SuparexTT 16:15:07 06/05/09 His tap handle broke (n/m) - zgene4 17:02:45 06/05/09 Correct - manis are fine (n/m) - ConVerTT 18:40:17 06/05/09 um (n/m) - ZiNnYc 17:29:32 06/05/09 Awesome - thnx for the humor and the pix! :B - yobobrox 19:01:50 06/05/09 test it on some AMS units ;) (n/m) - SuparexTT 19:16:01 06/05/09 Take it to a machine shop or call around. About 20 min of - AZHeat 16:11:52 06/06/09 Thnx, useful info (n/m) - yobobrox 00:28:46 06/07/09
Post a Followup	You cannot reply to this message because you are not logged in.