Subject	Help With Ideas for Access to Rear Coilover
Posted by	Warrz on April 22, 2009 at 1:29 AM
	This message has been viewed 282 times.
Message	I'm looking for pictures or ideas of what you may have done to provide access to the adjustment knobs on your rear coilovers? I'm looking at using a hole saw or trimming a 1.5 or so -inch dia. hole above the carbing strut brace slot to gain access through the interior piece that covers the tower for fat fingers. I've found some 1-2 inch plastic and rubber hole covers that I can color match the interior with SEMs paint. Pop the cover, adjust the knob and pop back on..... Anyone with a really clean install idea you can share? I'm trying to avoid just continuing the strut brace slot all the way up to the knob and then trimming the edge. I'd like to cover this area up since I won't need access that often.
Follow Ups	Help With Ideas for Access to Rear Coilover - Warrz 01:29:03 04/22/09 the best I have seen...although I have left mine open - LJZTT 01:44:17 04/22/09 Thats very similar - Warrz 02:07:19 04/22/09 I think it is Jegs that has a good assortment of caps/plugs (n/m) - LJZTT 02:17:17 04/22/09 Re: I think it is Jegs that has a good assortment of caps/plugs - got rice? 06:26:09 04/22/09 Thanks! (n/m) - Warrz 01:40:32 04/23/09 The holes for my caps are about 3/16" dia. if that. - not4resaleZ 09:42:50 04/22/09 The Zeal knob is about half-inch diameter. (n/m) - Warrz 01:32:45 04/23/09 Make that almost an inch in diameter (n/m) - Warrz 01:37:32 04/23/09 I use Tein Flex - Carlos Ramirez 06:35:24 04/22/09 I've never needed to adjust my SPL's while driving. - Guapo 08:22:45 04/22/09 LOL! ^ (n/m) - Twindragon 08:36:31 04/22/09 wierd it was there from the factory - Carlos Ramirez 10:03:28 04/22/09 your launching setup is backwards - aliaZ 10:10:20 04/22/09 2nd (n/m) - Piranha(PHX) 17:04:34 04/22/09 My SPL's work great at one setting for all situations - Guapo 11:02:22 04/22/09 Good for you then.. I like the adjustability - Carlos Ramirez 12:29:22 04/22/09 2nd. (although my SPLs aren't installed yet). - Inzane 10:17:00 04/22/09 What the hell is a EBDC? (n/m) - ZiNnYc 12:38:38 04/22/09 Should be EFDC...Electronic Force Dampning Control (n/m) - Gold Z 12:56:21 04/22/09 Actually, it's EDFC, Electronic Damping Force Controller (n/m) - Scotts94z32 13:29:26 04/22/09 bzzzt - collegeboy 15:20:26 04/22/09 What are the spring rates for the Z32 kit? - Scotts94z32 13:28:49 04/22/09 They are either 9/7 or 8/6, - ZiNnYc 13:45:27 04/22/09 What makes you say the z33 kit is overly stiff? (n/m) - kuah@splparts.com 14:58:11 04/22/09 Certainly over-stiff in the rear. The car doesn't plant as - Scotts94z32 09:40:59 04/23/09 ahh yes.. what a wonderful setup it is... (n/m) - KongZTT GT28RS MD 14:32:36 04/22/09 The Doctor says..... - Warrz 01:24:55 04/23/09 Re: I use Tein Flex - fourZero 01:40:34 04/23/09 Re: Help With Ideas for Access to Rear Coilover - awesome90tt 08:23:33 04/22/09 Looks good. Lots of space for adjustment. (n/m) - jschrauwen 10:25:24 04/22/09 Lots of leeway if the hole is off a bit too.... (n/m) - jzack 18:15:28 04/22/09 That's it! - Warrz 01:30:03 04/23/09 edfc ftw! - Madhatter10-6 12:16:58 04/22/09 DO you already have the shocks. Those other ones have the - MrPulldown 14:11:44 04/22/09 Re: DO you already have the shocks. - Warrz 01:15:42 04/23/09 Not completely stealth, but works great - pearl5 16:22:30 04/22/09 Nice. That seat cover is PIMP. (n/m) - BradZ (UF) 16:24:23 04/22/09 yeah, except up here, we don't sit on those, we wear them! (n/m) - ZEngineer 16:35:01 04/22/09 *date (n/m) - Guapo 20:09:53 04/22/09 That docking station would drive me nuts. (n/m) - MrPulldown 17:56:30 04/22/09 cool (n/m) - JustinSCZ32 18:38:49 04/22/09 That looks pretty good. Nice work. (n/m) - ZLover4Life 19:17:51 04/22/09
Post a Followup	You cannot reply to this message because you are not logged in.