Subject	I actually kind of like the chicken wire
Posted by	Stadsport on April 21, 2009 at 8:52 PM
	This message has been viewed 50 times.
In Reply To	Nice, but would look better without the chicken wire imo. (n/m) posted by TriniTT on April 21, 2009 at 08:48 PM
Message	But I think it should be painted flat black, and be cut to fit around the exhaust properly. Even better if you can put some kind of lining around the chicken wire where it meets the exhaust.
Follow Ups	Here's the finished product on the exhaust I posted - DAYTONAZ 20:42:54 04/21/09 Nice, but would look better without the chicken wire imo. (n/m) - TriniTT 20:48:28 04/21/09 I actually kind of like the chicken wire - Stadsport 20:52:28 04/21/09 ^^ You definitely need to do this, otherwise lose the mesh. (n/m) - J-Mart 21:04:46 04/21/09 I didn't think about painting it flat black, but that's an - DAYTONAZ 21:04:49 04/21/09 What exactly do you have in mind when you say - J-Mart 21:12:19 04/21/09 Re: What exactly do you have in mind when you say - DAYTONAZ 21:34:55 04/21/09 why not get someone to photoshop it in. (n/m) - d_flore 23:27:22 04/21/09 2nd and 2nd. - Z_Cherub 09:01:21 04/22/09 Black door edge guard - jschrauwen 11:57:46 04/23/09 Agreed. Nice job, but the wire cheapens the look. (n/m) - Yoshi 21:10:55 04/21/09 I like the wire and admire the look your going for. - LivinTheDream 21:32:19 04/21/09 Thanks, the openings don't leave me much choice - DAYTONAZ 21:41:54 04/21/09 Ah I see the holes. You dont have door fillers do you??? - LivinTheDream 23:40:06 04/21/09 No door fillers. I don't believe WW makes fillers for the - DAYTONAZ 15:06:47 04/22/09 Well done! (n/m) - Hiratsuka0689 (ATL) 20:49:31 04/21/09 That's not chicken wire... that's gutter guard :-) (n/m) - DAYTONAZ 20:59:37 04/21/09 The last pic is my favorite - induetime 21:07:56 04/21/09 Aren't you glad you didn't sell it. (n/m) - lazer(NV) 21:24:17 04/21/09 Well, that's what this is all for...when i'm done it's going - DAYTONAZ 14:06:45 04/23/09 win. tips remind me of a c6 vette. i dig the rear end. (n/m) - ali300zx 21:41:14 04/21/09 Lame. (n/m) - Dane (Houston) 22:11:45 04/21/09 The tips are very nice by themselves. When the mesh is - 240Z FeO2 22:43:59 04/21/09 I'm not sure if I like it or not but it's definitely - RAGTPZ 00:23:06 04/22/09 do the mesh with a holesaw somehow or ditch it altogether - LJZTT 00:45:44 04/22/09 Yeah that would be the extra step to make it look clean. (n/m) - SeedyROM 03:33:18 04/22/09 Holesaw? Don't think that'd work out too well. (n/m) - BigTDogg (MA) 07:31:06 04/22/09 I'd like to watch someone try ;) (n/m) - zgene4 09:13:33 04/22/09 HI!! instead of using a standard hole saw - Cap927(Boston) 10:47:07 04/22/09 Why on reverse? (n/m) - spotz 16:54:23 04/22/09 It doesn't grab it .... grinds it... (n/m) - jzack 18:21:23 04/22/09 I figured the mesh would need to be secured onto something - LJZTT 11:21:16 04/22/09 Sandwich it between two pieces of plywood... - Barry (NJ) 11:36:26 04/22/09 + C-clamps (n/m) - Z_Cherub 12:26:23 04/22/09 Hence the act of "sandwiching" it. (n/m) - BigTDogg (MA) 13:33:05 04/22/09 Didn't thing "sandwiching" automatically meant c-clapms. - Z_Cherub 17:58:08 04/23/09 Barry's method might work, but you can also just trace - BigTDogg (MA) 13:34:33 04/22/09 Even the gutter guard from HD is AL. (n/m) - Barry (NJ) 14:39:55 04/22/09 not all, they do have galvanized as well (n/m) - Cap927(Boston) 08:31:29 04/23/09 exactly what I was thinking. (n/m) - ZLover4Life 19:22:00 04/22/09 I heard you were really tough on dikes (n/m) - LJZTT 20:53:29 04/22/09 Apparently my reputation precedes me :-) (n/m) - BigTDogg (MA) 07:52:37 04/23/09 hey Tony, I tried emailing you but no repply - Cap927(Boston) 12:45:44 04/22/09 MAN!! You got my cell #, I was out all morning - BigTDogg (MA) 13:32:24 04/22/09 Could not find it, lost some contacts on my BBerry - Cap927(Boston) 14:07:21 04/22/09 Well something to make it round. Might have to do it by hand (n/m) - SeedyROM 20:48:59 04/22/09 The pink ride is sweet! What does it run in the 1/4? (n/m) - phillyz 04:13:39 04/22/09 I'll mod that next. (n/m) - DAYTONAZ 15:03:28 04/22/09 Re: Here's the finished product on the exhaust I posted - racer2fst 08:42:32 04/22/09 Thanks, the wheels are another project that's almost done - DAYTONAZ 15:01:37 04/22/09 Have you thought about bumps and vibration? (n/m) - Neogenesis 17:48:56 04/22/09
Post a Followup	You cannot reply to this message because you are not logged in.