Subject	That is exactly what I am saying.
Posted by	na300zx (OH) on April 20, 2009 at 11:38 AM
	This message has been viewed 248 times.
In Reply To	So what you're saying is that you need several too break posted by Machtavian on April 20, 2009 at 11:04 AM
Message	I'm not saying that you shouldn't tell people that he broke his crankshaft in his 1k RWHP Z. I know there aren't many 1k rwhp Z32s out there, so it will be hard to tell what the limit is, but just because one broke doesn't mean a whole lot. There are far too many variables to say that his crank was at its limit. That's all I'm saying. Click to see how intelligent our leadership really is... Biden Pelosi Obama Obama
Follow Ups	The 1009rwhp beast snapped the crank at the drag strip... - Machtavian 21:01:21 04/19/09 What other damage did it cause? - FuerGrissa 21:07:45 04/19/09 Not sure unil it gets torn apart... - Machtavian 21:11:45 04/19/09 *probably* (n/m) - Machtavian 21:14:07 04/19/09 Well that sucks :( (n/m) - collegeboy 21:09:32 04/19/09 that really sucks - komplexZTT 21:38:23 04/19/09 Interesting! Never seen one break during a burn out (n/m) - John@Z1 21:39:31 04/19/09 All that money lost. Sucks to hear. (n/m) - rojoloco (San Diego) 21:44:51 04/19/09 Re: The 1009rwhp beast snapped the crank at the drag strip... - WazTTed 21:45:22 04/19/09 Re: Re: The 1009rwhp beast snapped the crank at the drag strip... - Tech@EPR 21:57:15 04/19/09 Just tring to make people aware of the problem... - Machtavian 11:16:22 04/20/09 At what power levels is the RB26 crank breaking? - Scotts94z32 12:44:45 04/20/09 Re: Just tring to make people aware of the problem... - Tech@EPR 17:36:04 04/20/09 Does it have a LW underdrive pulley? - Spddracer 21:45:30 04/19/09 2nd. Something rotating isnt right. Pulley, or as Tech@epr - 5280Z_nightstalker 22:13:22 04/19/09 Re: The 1009rwhp beast snapped the crank at the drag strip... - Tech@EPR 21:48:56 04/19/09 I was just going to quote you saying it was rated at 2000hp - KevinZtwin 21:52:16 04/19/09 Big 2nd. (n/m) - Red Baron Z 21:58:56 04/19/09 Escort Racing used a stock crank on their 1200whp+ drag Z32. - 952+2TT 21:57:24 04/19/09 what was he running for a crank pulley? - aliaZ 22:33:05 04/19/09 2nd, at that level an ATI is a MUST. - zboost(NoVA) 00:10:34 04/20/09 Re: 2nd, at that level an ATI is a MUST. - Tech@EPR 00:21:14 04/20/09 $510 @ bde ;-) (n/m) - LitlElvis 00:42:33 04/20/09 Glad I have one (n/m) - collegeboy 00:43:57 04/20/09 Re: $510 @ bde ;-) - Tech@EPR 00:53:27 04/20/09 Standard UR pulley... - Machtavian 10:58:53 04/20/09 sucks, was it on the first run of the day or did he get runs - tya 22:33:12 04/19/09 =-) (n/m) - nemo1080 (Iowa) 00:15:25 04/20/09 Re: The 1009rwhp beast snapped the crank at the drag strip... - Rob260 00:57:20 04/20/09 Always be on a lower boost/rpm when doing your burn out. - Jason300zxTT 07:46:01 04/20/09 Just because one broke doesn't mean you have found - na300zx (OH) 08:01:49 04/20/09 Agreed. (n/m) - Scotts94z32 10:16:03 04/20/09 So what you're saying is that you need several too break - Machtavian 11:04:25 04/20/09 That is exactly what I am saying. - na300zx (OH) 11:38:08 04/20/09 Yes. He is saying that a sample size of one is not - 300NASeattle 15:06:37 04/20/09 Somewhat true. As it could be the general area where the - mds2004 17:25:04 04/21/09 Bummer! That sucks (n/m) - Z_Pilot 10:03:32 04/20/09 Sucks. As mentioned above, I wouldn't state this as a new - TheTwinZ (Peru) 10:14:26 04/20/09 Here's my take on it... - CaliguyPurdue (redesigning) 14:18:09 04/20/09 Mmmm, Wallner lines. (n/m) - Scotts94z32 15:48:26 04/20/09 Has anyone analyzed our crank material? - Ashman2k2 16:13:24 04/20/09 It would be a pretty complex simulation... - CaliguyPurdue (redesigning) 16:36:48 04/20/09 I understand what you are saying, but I was looking for a - Ashman2k2 17:57:59 04/20/09 Re: Has anyone analyzed our crank material? - Tech@EPR 17:28:19 04/20/09 Nice! that would be awesome (n/m) - Ashman2k2 18:08:16 04/20/09 i <3 Metalorgy (n/m) - Adam (NoVA) 08:40:40 04/21/09 D'oh, sorry to hear (n/m) - TT XTZ 16:48:54 04/20/09 You mentioned that the assembly was NOT balanced right? - Seb@Specialty-Z 17:51:08 04/20/09 wow - aliaZ 18:46:45 04/20/09
Post a Followup	You cannot reply to this message because you are not logged in.