Subject	My take on it:
Posted by	94Z32XTT on March 05, 2009 at 12:22 AM
	This message has been viewed 233 times.
In Reply To	a little dilema posted by Alan(MD/NJ) on March 04, 2009 at 04:12 PM
Message	If the buyer was clear and told you that he had a set of 2.4" test pipes and specifically asked you if the test pipes you were selling were 2.5", then you are responsible to take them back if they are in fact as YOU stated (2.4"). To me .1" would be waste of time and not worth the hassles, but you are the one who was aware of his specific requirements and should take them back and return his money including shipping charges due to an error in measurement. It doesn't matter if you want them back or not, just return his money and try reselling them if YOU made the mistake! If HE didn't tell you his situation, then you would have had a case.
Follow Ups	a little dilema - Alan(MD/NJ) 16:12:14 03/04/09 He should have asked for a pic w/ measurements. - SuparexTT 16:17:33 03/04/09 This is a good idea. Have him SHOW you it's 2.4" (n/m) - Yoshi 17:58:12 03/04/09 He is just looking for a reason to complain/get money back - alpha_omega16 16:29:29 03/04/09 Re: a little dilema - ali300zx(Irani) 17:05:50 03/04/09 i dont want/ need them back - Alan(MD/NJ) 18:03:33 03/04/09 returning them would be for his benefit, not yours. - ali300zx(Irani) 18:21:30 03/04/09 Which brand TPs are they? (n/m) - Scotts94z32 17:27:31 03/04/09 2nd, that should settle it. (n/m) - zgene4 18:30:33 03/04/09 z1, i may even have the receipt from the previous owner (n/m) - Alan(MD/NJ) 19:08:23 03/04/09 IIRC, older Z1 TPs were 2.4". They just recently made 2.5" (n/m) - BigTDogg (MA) 19:56:22 03/04/09 i have a receipt of the 2.5" test pipes - Alan(MD/NJ) 04:25:11 03/05/09 Too bad, all sales final. (n/m) - BigTDogg (MA) 17:35:53 03/04/09 Be careful, he might be trying to send...... - Multi_Read (MO) 17:53:03 03/04/09 In the state of NJ... if a buyer wants to return it because - resorb (NJ) 18:57:44 03/04/09 I think its more like a seller isnt obligated to accept - John B. (NJ) 19:41:19 03/04/09 I am the buyer - 600rr 19:51:07 03/04/09 pics - 600rr 19:54:14 03/04/09 What are you using to measure, and what are you measuring? - John B. (NJ) 20:15:39 03/04/09 I'm using a small tape measure. - 600rr 20:43:33 03/04/09 Well, it could certainly be a misunderstanding... - John B. (NJ) 20:58:07 03/04/09 A tape measure cannot be used to measure an OD... - CaliguyPurdue (redesigning) 22:03:25 03/04/09 Get over it pretty sure the seller did not say 2.5 - dream Z (MD) 22:16:52 03/04/09 WTF? .1" isn't worth bickering over. Can you even feel a - 600ZXR 21:08:55 03/04/09 If in fact they are 2.4" pipes....it is since the guy - Ashman2k2 22:13:58 03/04/09 Send him a write-up on how to use a micrometer (n/m) - njz 21:21:41 03/04/09 Is .1 of an inch really that big of a deal. - dream Z (MD) 22:07:49 03/04/09 I already had 2.4" - 600rr 22:30:53 03/04/09 Here is what you need to do - Ashman2k2 23:19:37 03/04/09 thanks - 600rr 23:27:08 03/04/09 Yes he was talking about measuring the circumference - Agner.S(CT) 23:29:11 03/04/09 ahh - 600rr 00:02:21 03/05/09 My take on it: - 94Z32XTT 00:22:22 03/05/09 On the one hand, it's the principle of the thing, but on the - davidztt 01:20:06 03/05/09 I hear you david - 600rr 02:08:33 03/05/09
Post a Followup	You cannot reply to this message because you are not logged in.