Subject	What are you using to measure, and what are you measuring?
Posted by	John B. (NJ) on March 04, 2009 at 8:15 PM
	This message has been viewed 118 times.
In Reply To	I am the buyer posted by 600rr on March 04, 2009 at 07:51 PM
Message	Inner or outter diameter?
Follow Ups	a little dilema - Alan(MD/NJ) 16:12:14 03/04/09 He should have asked for a pic w/ measurements. - SuparexTT 16:17:33 03/04/09 This is a good idea. Have him SHOW you it's 2.4" (n/m) - Yoshi 17:58:12 03/04/09 He is just looking for a reason to complain/get money back - alpha_omega16 16:29:29 03/04/09 Re: a little dilema - ali300zx(Irani) 17:05:50 03/04/09 i dont want/ need them back - Alan(MD/NJ) 18:03:33 03/04/09 returning them would be for his benefit, not yours. - ali300zx(Irani) 18:21:30 03/04/09 Which brand TPs are they? (n/m) - Scotts94z32 17:27:31 03/04/09 2nd, that should settle it. (n/m) - zgene4 18:30:33 03/04/09 z1, i may even have the receipt from the previous owner (n/m) - Alan(MD/NJ) 19:08:23 03/04/09 IIRC, older Z1 TPs were 2.4". They just recently made 2.5" (n/m) - BigTDogg (MA) 19:56:22 03/04/09 i have a receipt of the 2.5" test pipes - Alan(MD/NJ) 04:25:11 03/05/09 Too bad, all sales final. (n/m) - BigTDogg (MA) 17:35:53 03/04/09 Be careful, he might be trying to send...... - Multi_Read (MO) 17:53:03 03/04/09 In the state of NJ... if a buyer wants to return it because - resorb (NJ) 18:57:44 03/04/09 I think its more like a seller isnt obligated to accept - John B. (NJ) 19:41:19 03/04/09 I am the buyer - 600rr 19:51:07 03/04/09 pics - 600rr 19:54:14 03/04/09 What are you using to measure, and what are you measuring? - John B. (NJ) 20:15:39 03/04/09 I'm using a small tape measure. - 600rr 20:43:33 03/04/09 Well, it could certainly be a misunderstanding... - John B. (NJ) 20:58:07 03/04/09 A tape measure cannot be used to measure an OD... - CaliguyPurdue (redesigning) 22:03:25 03/04/09 Get over it pretty sure the seller did not say 2.5 - dream Z (MD) 22:16:52 03/04/09 WTF? .1" isn't worth bickering over. Can you even feel a - 600ZXR 21:08:55 03/04/09 If in fact they are 2.4" pipes....it is since the guy - Ashman2k2 22:13:58 03/04/09 Send him a write-up on how to use a micrometer (n/m) - njz 21:21:41 03/04/09 Is .1 of an inch really that big of a deal. - dream Z (MD) 22:07:49 03/04/09 I already had 2.4" - 600rr 22:30:53 03/04/09 Here is what you need to do - Ashman2k2 23:19:37 03/04/09 thanks - 600rr 23:27:08 03/04/09 Yes he was talking about measuring the circumference - Agner.S(CT) 23:29:11 03/04/09 ahh - 600rr 00:02:21 03/05/09 My take on it: - 94Z32XTT 00:22:22 03/05/09 On the one hand, it's the principle of the thing, but on the - davidztt 01:20:06 03/05/09 I hear you david - 600rr 02:08:33 03/05/09
Post a Followup	You cannot reply to this message because you are not logged in.