Subject	If you are going to go through the hassle of removing
Posted by	cossiemodo2000 on February 19, 2009 at 12:23 PM
	This message has been viewed 69 times.
In Reply To	Compression results finally. Looking for general posted by ZEVAN (Ca) on February 19, 2009 at 12:09 PM
Message	the motor to do work on turbos, I recommend you atleast refresh the block with new bearings and rings. Your planned mods will add some more stress on the engine.
Follow Ups	Compression results finally. Looking for general - ZEVAN (Ca) 12:09:32 02/19/09 If you are going to go through the hassle of removing - cossiemodo2000 12:23:17 02/19/09 Also have the decks checked (n/m) - lazer(NV) 12:31:12 02/19/09 Really? Thats way over my head. I was hoping I would - ZEVAN (Ca) 12:39:43 02/19/09 thats over kill - Carlos Ramirez 12:51:35 02/19/09 I strongly disagree. opening the block is huge investm (n/m) - AntiHero 13:34:21 02/19/09 Strongly 2nded. (n/m) - Yoshi 15:00:02 02/19/09 Feel my current pain. I agree. (n/m) - SuparexTT 15:40:02 02/19/09 Wheel police. Why not Ash? Usually no prob's with ECU's. - 91Z32TT 12:30:54 02/19/09 I've heard that his tend to be more on the - ZEVAN (Ca) 12:37:48 02/19/09 Ash's tune passes Smog check, plus no det in hot FL temps (n/m) - SkiFly01 12:53:21 02/19/09 91 octane - ZEVAN (Ca) 13:01:10 02/19/09 Call 818-703-6272 for a good tune. (n/m) - Piranha(PHX) 12:58:18 02/19/09 Yeah...I didn't realize they did eprom's. I thought - ZEVAN (Ca) 13:03:48 02/19/09 I think I saw that written on a gas station bathroom wall (n/m) - CaliguyPurdue (redesigning) 14:03:16 02/19/09 No, that said "time", and the number started with 765 5... (n/m) - Scotts94z32 14:45:00 02/19/09 ^^^plug^^^ =-) (n/m) - nemo1080 (Iowa) 18:07:27 02/19/09 IMO, I wouldn't even order a chip from the guy. - Josher 14:09:20 02/19/09 Ash ecu tend to be on the lean side and his customer - boost420 14:58:52 02/19/09 My car runs rich. What are you talking about? (n/m) - TT95ZX (formerly amp300zx) 17:03:02 02/19/09 Re: My car runs rich. What are you talking about? - boost420 00:33:07 02/20/09 And you used a wideband to check right ? Or did it just - ztunerz 09:12:28 02/20/09 Since compression is good and.... - The Hawk 13:09:09 02/19/09 Compression numbers are alright just dont expect them to - 5280Z_nightstalker 15:14:44 02/19/09 Re: Compression numbers are alright just dont expect them to - ali300zx(Irani) 15:26:22 02/19/09 Not saying its weaker I was hoping to avoid this confusion - 5280Z_nightstalker 15:38:23 02/19/09 Well, my motor is... - SuparexTT 15:43:22 02/19/09 All your cylinders are very close to each other... - SuparexTT 15:45:31 02/19/09 Thanks for the advice. Maybe someone who has tested - ZEVAN (Ca) 17:28:16 02/19/09 Re: Compression results finally. Looking for general - Z300Z 10:36:46 02/20/09
Post a Followup	You cannot reply to this message because you are not logged in.