Subject	You will most likely be grinding the bell housing. (n/m)
Posted by	Spddracer on January 28, 2009 at 6:23 PM
	This message has been viewed 71 times.
In Reply To	yeah i know. i misunderstood spddracer. you shouldnt have to posted by LivinTheDream on January 28, 2009 at 05:37 PM
Message
Follow Ups	Going Shopping (Parts List) any suggestions - LivinTheDream 15:04:24 01/28/09 save the chra money and get new turbos? - nemo1080 (Iowa) 15:10:42 01/28/09 I just got done a rebuild a few weeks ago so .. - LivinTheDream 15:21:25 01/28/09 i guess the chra desicion for me would be based mailey - nemo1080 (Iowa) 15:30:05 01/28/09 I will probably get the plenum and header gaskets as well - LivinTheDream 15:39:55 01/28/09 yeah, thats probably ok for the most part - nemo1080 (Iowa) 16:04:47 01/28/09 "X" series clutch/flywheel - Spddracer 15:20:45 01/28/09 Why wouldnt i need to shim out my starter???? - LivinTheDream 15:34:15 01/28/09 Do you already have the TT JWT flywheel? - Spddracer 15:48:27 01/28/09 Glad u know your stuff. Well I have an old NA flywheel... - LivinTheDream 15:58:41 01/28/09 The TZ wares much longer than the Rally/organic. - Spddracer 16:43:43 01/28/09 Dont have the TT flywheel yet. But I rather one over NA - LivinTheDream 17:48:07 01/28/09 I don't think you're getting the point here. - Spddracer 18:22:40 01/28/09 The X series clutches are of a newer design... - apudapus 23:35:16 01/28/09 OH. SO Sorry I wasnt gettin it before man. - LivinTheDream 17:54:00 01/29/09 Listen to Joe. He won't steer you wrong. - rojoloco (San Diego) 02:09:02 01/29/09 If it goes direct 2 an NA will it also bolt on to a TT wheel (n/m) - LivinTheDream 16:03:49 01/28/09 No - the NA flywheel has a smaller diameter then the TT one. (n/m) - Bernie (NoVA) 16:05:59 01/28/09 yeah. I remember when i was doing my na->TT - SlowZ(SD) 17:25:49 01/28/09 yeah i know. i misunderstood spddracer. you shouldnt have to - LivinTheDream 17:37:19 01/28/09 I used TT flywheel on NA tranny (n/m) - SlowZ(SD) 17:44:14 01/28/09 You will most likely be grinding the bell housing. (n/m) - Spddracer 18:23:17 01/28/09 No prob. Sorry if I dont get what you were saying.. - LivinTheDream 20:28:17 01/28/09 1 MORE THING. should i get new springs for the TOB arm (n/m) - LivinTheDream 20:29:25 01/28/09 They are rather inexpensive. (n/m) - Bernie (NoVA) 21:02:49 01/28/09 if its messed up yea - Drk93TT 21:09:08 01/28/09 Thanks a tone guys : ) (n/m) - LivinTheDream 21:14:52 01/28/09 TON (n/m) - LivinTheDream 21:15:21 01/28/09 Swap all hoses out with nice silicone - fst300zx 21:48:00 01/28/09
Post a Followup	You cannot reply to this message because you are not logged in.