Subject	Keep in mind the couplers he is using are 90's.
Posted by	Woody75 (Denver) on December 10, 2008 at 11:50 AM
	This message has been viewed 82 times.
In Reply To	Do you remember the diameters on the inlet and outlet posted by BigTDogg (MA) on December 10, 2008 at 08:27 AM
Message	The metal elbow pipes were tighter than 90 degrees. He is using smaller filters than the pop charger as well. So they have room to point towards each other some as you can see in the pis. With 2 pop chargers you'll want the tighter bends the metal elbows provide to make everything fit correcty as the filters will pretty much be touching each other. Z1 sells the metal elbows and I think there is a kit on ebay they uses them as well but with the smaller K&N type filters. JackB nimble JackB quick JackB can suck my dick =P - james-lee 11/02/01 Arrogance is the #1 weapon against Supra Owners - MikeH 08/06/02 Dallas with a Z: I like the bulge dude 05/02/03 Bezbefootball: Does dick have anything for me? 10/21/03
Follow Ups	2 Intakes!!! - Fares300zx 02:26:02 12/10/08 There are two filters, but the air still has to go through - turtleboy 02:41:34 12/10/08 Please, start using this site's search feature. - SactoTodd 04:47:36 12/10/08 2nd'd. And lay off the use of "???" & "!!!" with every post. (n/m) - Dave N 10:19:56 12/10/08 How do they know??? - scottyfender 07:41:52 12/10/08 THIS, is how you do dual intakes proper - BigTDogg (MA) 08:13:12 12/10/08 That is a good way of doing it but running them - dream Z (MD) 09:31:28 12/10/08 Two MAFs vs One+Dummy - JMWS.TTZ 10:21:18 12/10/08 S-AFC (n/m) - ZLover4Life 10:31:14 12/10/08 there is a write up under the faq section (n/m) - dream Z (MD) 12:46:33 12/10/08 proper - Adam (NoVA) 11:17:46 12/10/08 Same thing, with a better sig :-) (n/m) - BigTDogg (MA) 11:42:07 12/10/08 & no teeny tiny stock oil cooler :) (n/m) - Adam (NoVA) 13:35:19 12/10/08 Boo for light beer. (n/m) - TriniTT 13:46:40 12/10/08 Yup - TT XTZ 11:46:48 12/10/08 did mine under $70 - SkiFly01 08:22:48 12/10/08 Do you remember the diameters on the inlet and outlet - BigTDogg (MA) 08:27:18 12/10/08 I used a 2" to 2.5" 90 degree coupler (n/m) - SkiFly01 08:31:33 12/10/08 You sure it isn't a 3" to 2" reducer coupler? - immortaliZed 10:36:08 12/10/08 Stock pipe is 2.5". Maf is closer to 3". So 2.5"-3" (n/m) - Woody75 (Denver) 11:42:09 12/10/08 yep you are correct, i just looked at my original post... - SkiFly01 13:02:47 12/10/08 Keep in mind the couplers he is using are 90's. - Woody75 (Denver) 11:50:25 12/10/08 cool way of doing it. I think I will have to go with - upcominZ_(NOLA) 12:33:21 12/10/08 Here's my setup - TTFairladyZ 16:39:58 12/10/08 Yo upcominZ_(NOLA), your post is locked, so I'll write here - BigTDogg (MA) 15:43:28 12/11/08
Post a Followup	You cannot reply to this message because you are not logged in.