Subject	I have pretty much the same setup.
Posted by	MY3ZTT on December 07, 2008 at 8:39 PM
	This message has been viewed 66 times.
In Reply To	Z1 725 turbos posted by wthreez 2+2 TT on December 06, 2008 at 11:26 PM
Message	I'm in the same boat as you with finally breaking the engine in. I have a fully built stage 5 IPP longblock with all the goodies (manifolds, 500 cams, 3" exhaust) and these turbos do hit pretty hard. I'm just running off the wastegates and 15psi is what mine are set at and I reach full boost around 4400 rpm. To be honest i was expecting a little more when i fully floored it but i'm still not tuned. I think these turbos will really hit once its tuned and i turn the boost up to 20psi. I guess 15 psi is "baby boost" for these turbos and they are barely coming alive at that boost. Good luck with your setup.
Follow Ups	Z1 725 turbos - wthreez 2+2 TT 23:26:41 12/06/08 With the manifolds and 3" exhaust, it's still laggy? - ZXRider(SoCal) 23:29:47 12/06/08 I got everything I could think of that would help spool them - wthreez 2+2 TT 23:40:47 12/06/08 Sounds like fun. If the base boost is 15 lbs (or more) - SirpriZ 23:44:09 12/06/08 Re: Sounds like fun. If the base boost is 15 lbs (or more) - wthreez 2+2 TT 23:50:31 12/06/08 Yeah, big difference between 91 and 93 (two). I don't - SirpriZ 11:56:40 12/07/08 I have GT600R's and you can run 18psi on 93 octane safely (n/m) - amp300zx 12:01:13 12/07/08 Go ahead and rub it in! Mark (n/m) - SirpriZ 12:03:12 12/07/08 For you grammar Nazis: *you're fine*. What the hell - SirpriZ 12:05:55 12/07/08 Texas urine is 93 octane (n/m) - aliaZ 23:53:20 12/06/08 Didnt know you were from tx Aliaz. For all dfw Zers here - wthreez 2+2 TT 00:54:09 12/07/08 have you used them before? - aliaZ 13:33:28 12/07/08 You guys from Texas do everything better and bigger, - SirpriZ 12:01:46 12/07/08 I'll take you up on that offer probably early next year - aliaZ 13:30:25 12/07/08 Add some Cams!!! JWT 500s would be a nice addition. (n/m) - MixManMash 01:54:56 12/07/08 I was told not to do cams unless I was doing valves etc.... - wthreez 2+2 TT 02:02:10 12/07/08 who told you that? - Waggz 02:12:13 12/07/08 Right, but you could get the cheaper mild cams. (n/m) - Dane (Houston) 02:29:07 12/07/08 Waste of money. Go 400+ or 500, or nothing. (n/m) - Inzane 14:03:13 12/07/08 poor advice (n/m) - aliaZ 13:31:25 12/07/08 When they hit though I bet its a ride... (n/m) - amp300zx 11:27:07 12/07/08 i could only image spinning tires at 70. - eyagel (Houston) 13:25:26 12/07/08 What tires are you using? (n/m) - Ashman2k2 13:51:46 12/07/08 I have pretty much the same setup. - MY3ZTT 20:39:44 12/07/08
Post a Followup	You cannot reply to this message because you are not logged in.