Subject	The only people that do that here are the 50 y/o attorneys
Posted by	Z_Cherub on October 29, 2008 at 10:37 AM
	This message has been viewed 50 times.
In Reply To	Ok, what about just hard enough to bend the plastic one. posted by Woody75 (Denver) on October 29, 2008 at 08:26 AM
Message	wives driving Corvettes/Porches. Don't drive like them and all will be well. Seriously, though, I would imagine that the same kind of scratch that you'll see on the bottom of the fascia from an incident like that will show up on the bottom of the splash shield. I don't see any reason why such a minor run-in would cause it to warp/bend/break.
Follow Ups	Front Splash Shield Update - Spddracer 22:30:40 10/28/08 right on!! ill make an order probably this week. - fst300zx 22:47:40 10/28/08 question - LJZTT 22:50:30 10/28/08 Radiator drain is accessed w. the engine shield down. (n/m) - Bernie (NoVA) 23:34:14 10/28/08 mine has a little velcro trap door (n/m) - LJZTT 12:04:43 10/29/08 Yours is plastic :)- (n/m) - Spddracer 17:12:16 10/29/08 **velcro'd, sorry (n/m) - LJZTT 19:57:49 10/29/08 The Drain is behind the rear shield, This is the front one. - Spddracer 06:46:12 10/29/08 sorry I meant the draincock or whatever it is called on - LJZTT 12:08:13 10/29/08 Yes, all the stock shields have that. - Woody75 (Denver) 12:15:03 10/29/08 I see your point. I guess not many other ppl use this method - LJZTT 12:25:31 10/29/08 Correct, most people don't dump coolant on the ground. - Woody75 (Denver) 13:37:20 10/29/08 *shrug - LJZTT 14:14:07 10/29/08 So you are agreeing with me? - Woody75 (Denver) 14:28:19 10/29/08 taking off two shields and reinstalling, or don't touch them - LJZTT 17:56:22 10/29/08 In short, you are in idiot. - Woody75 (Denver) 18:53:53 10/29/08 Fine be an asshole, no one was asking you to begin with - LJZTT 19:36:19 10/29/08 Where did I get worked up exacty? - Woody75 (Denver) 22:20:32 10/29/08 Again Tim, I have no need to remove with the shields to - LJZTT 17:03:19 10/30/08 Can you ever forgive me? (n/m) - Woody75 (Denver) 22:09:03 10/30/08 How many people have stock radiators with the drain cock - Spddracer 19:27:53 10/29/08 I don't know, but if I had to guess - LJZTT 19:51:06 10/29/08 ...along with one of those clutches! (n/m) - LJZTT 19:53:58 10/29/08 Question - Woody75 (Denver) 22:57:12 10/28/08 i doubt he crash tested it... geez (n/m) - fanta-z 23:55:32 10/28/08 Drive carefully is my only advice. - rojoloco (San Diego) 00:56:09 10/29/08 I think it would probably just bend under. - Spddracer 06:44:13 10/29/08 Ok, what about just hard enough to bend the plastic one. - Woody75 (Denver) 08:26:13 10/29/08 The only people that do that here are the 50 y/o attorneys - Z_Cherub 10:37:00 10/29/08 I don't see a problem. The way the front of it is designed - Spddracer 11:35:59 10/29/08 With all those choices, I can't decide which one to get! (n/m) - Musashi Sword 09:07:15 10/29/08 going to offer rear PC'ed to match? (n/m) - FuerGrissa 09:07:20 10/29/08 Working on the pricing now. Should know soon. (n/m) - Spddracer 11:36:48 10/29/08
Post a Followup	You cannot reply to this message because you are not logged in.