Subject	I can understand, but in the end it is all going to come out
Posted by	Ash's Z on September 08, 2008 at 11:26 PM
	This message has been viewed 577 times.
In Reply To	Sorry Ash, I've disclosed as much information as I care to. (n/m) posted by LitlElvis on September 08, 2008 at 11:16 PM
Message	anyhow. I'm not asking for spring rates from you - all I Am asking for is what method you used to overcome the fact it requires an impact on the VTC mechanism in order for it to break free and rotate. You can't just apply torque to it and take a measurement - the device's structure requires a bit of shock to allow any motion at all. I've found here on the bench that it takes around 25ft/lbs PLUS a good smack on the VTC in order to make it rotate at all. I can put up to 66lbs of force on it and it wont turn at all unless I smack it. And from the results I just found in this post: [ http://twinturbo.net/nissan/300zx/forums/general/view/2199447/I-also-dont-see-how-two-high-tension-valve-springs-acting.html ] There just isn't enough torque from the cam to overpower the VTC mechanism, even if you smack it. [ ashspecz.com ] [ agpowers@bellsouth.net ] Enthusiasts soon understand each other. --W. Irving. Are you an enthusiast? If you are out to describe the truth, leave elegance to the tailor. Albert Einstein
Follow Ups	OK, Ash wanted my input on just the VTC noise - DVDBURN (MD) 12:36:37 09/08/08 oops! Link to service bulletin. - DVDBURN (MD) 12:52:56 09/08/08 So the 90 to 91 Cam Sprokets are more prone to this any ways - Sleeper_TTZ(SeKy) 13:22:49 09/08/08 They won't fit. (n/m) - na300zx (OH) 13:24:31 09/08/08 Have to change the cam's also???? (n/m) - Sleeper_TTZ(SeKy) 13:25:20 09/08/08 Yeah. Unless you already have new style cams - na300zx (OH) 13:32:32 09/08/08 Well no i'm still useing my old cams. I have a set off a NA - Sleeper_TTZ(SeKy) 14:45:24 09/08/08 I am under the impression that auto tranny cars have less - na300zx (OH) 14:55:43 09/08/08 i read the intake cams on an auto tt are slightly smaller, - ricky6991 15:36:52 09/08/08 I had 1 new style sprocket on my '91 cams with no issues > - my91z 14:34:55 09/08/08 There are two types of new style sprockets - na300zx (OH) 14:49:26 09/08/08 Learn something new everyday..... (n/m) - my91z 14:53:30 09/08/08 Yup. Just when you think you know it all, someone - na300zx (OH) 14:58:00 09/08/08 I bought a set of used late model sprockets so that - AZHeat 14:28:17 09/08/08 Progress is nice - FuerGrissa 13:55:04 09/08/08 I think this is the most intelligent VTC comment yet.. - The Devils Z 15:05:41 09/08/08 Question on the service bulletin. - Woody75 (Denver) 14:59:02 09/08/08 I don't know Tim. I would guess it's refering to the light - DVDBURN (MD) 17:43:01 09/08/08 Blasphemy! Ashlah Akbar! (n/m) - Tennyson (ATL) 15:58:47 09/08/08 I'm confused more by reading your post... - ni[X]it 18:24:56 09/08/08 All I want to know is if the BDE rebuilt gears - plower 19:16:27 09/08/08 the BDE gears are much cheaper than new - aliaZ 19:45:36 09/08/08 This is a decision that YOU should make for yourself. (n/m) - LitlElvis 20:59:22 09/08/08 Thanks for your reply. - DVDBURN (MD) 19:23:06 09/08/08 Sorry if it came off wrong. - ni[X]it 20:39:15 09/08/08 Not at all! As they say, it's all good ;) (n/m) - DVDBURN (MD) 07:44:08 09/09/08 LOL! - collegeboy 19:26:00 09/08/08 I have almost 9000 miles on BDE sprockets..NO NOISE (n/m) - citation 20:45:21 09/08/08 Sorry but I have to kick this dead horse some more... - LitlElvis 20:52:08 09/08/08 Thanks Brett. - DVDBURN (MD) 21:00:54 09/08/08 No Gary. I do not agree that new internals did anything. - LitlElvis 21:17:29 09/08/08 AGain, I didn't use "newer" internals. I used the same - Ash's Z 09:58:39 09/09/08 I like pictures... - John B. (NJ) 21:04:00 09/08/08 The numbers would be irrelevent. - ni[X]it 21:11:06 09/08/08 Point taken... - John B. (NJ) 21:29:53 09/08/08 It's more like 0.809:1, but it's still linear. - LitlElvis 06:52:12 09/09/08 Hi Gary, thanks for the clarification. - Ash's Z 21:42:46 09/08/08 Brett, Q about your plot and the paragraph below it: - Ash's Z 22:33:54 09/08/08 Sorry Ash, I've disclosed as much information as I care to. (n/m) - LitlElvis 23:16:33 09/08/08 I can understand, but in the end it is all going to come out - Ash's Z 23:26:28 09/08/08 I also dont see how two high-tension valve springs acting - Ash's Z 23:16:58 09/08/08 I would be happy to make a short video real quick showing - Ash's Z 23:38:20 09/08/08 VIdeo made >>> - Ash's Z 03:12:00 09/09/08 Bravo Ash, you've come a long way in just two days! - LitlElvis 06:49:00 09/09/08 Well, I have concerns with the fact the cam wont just - Ash's Z 09:46:13 09/09/08 Uh, I'm Gary :) (n/m) - DVDBURN (MD) 22:44:59 09/08/08 I said 5K, if you want to do 8K that's ok too. (n/m) - LitlElvis 23:07:43 09/08/08 Good deal - we'll make it 8K then. (n/m) - Ash's Z 03:14:03 09/09/08 If I were to speculate based on my findings, your Y axis - Ash's Z 09:42:08 09/09/08 Re: OK, Ash wanted my input on just the VTC noise - Ash's Z 21:35:10 09/08/08 Ok Ash, whatever makes you happy :) - DVDBURN (MD) 22:55:00 09/08/08 Well, it isn't a matter of that at all. IT is a matter of - Ash's Z 23:19:37 09/08/08 I'll look at it later, after the football game :) (n/m) - DVDBURN (MD) 23:43:45 09/08/08 Does the newer version have a wider thrust face? (n/m) - CaliguyPurdue (redesigning) 01:04:21 09/09/08 No, only difference is the seal on the cam helix and the - Ash's Z 02:02:32 09/09/08 Also, Gary, I use the newer VTC sprockets in my engine. - Ash's Z 09:56:13 09/09/08 Also Ash,........ - DVDBURN (MD) 20:05:00 09/09/08 Hi Gary, - Ash's Z 09:46:22 09/10/08 Fair enough. Hope it works out. (n/m) - DVDBURN (MD) 10:00:58 09/10/08
Post a Followup	You cannot reply to this message because you are not logged in.