Subject	Ever removed your exhaust? It's pretty straight forward
Posted by	91Z32TT on August 13, 2008 at 3:43 PM
	This message has been viewed 84 times.
In Reply To	How much of a pain to replace a starter? posted by Timmy on August 13, 2008 at 03:38 PM
Message	I can't recall if you need to take the downpipe off as well, but it's either just the midpipe, or the midpipe and downpipe from the passenger side that you have to remove. After that, it's 1 12mm nut, 1 12mm bolt, and I believe another 12mm bolt holding a wiring harness down. Take those out, unbolt the power wire from the starter itself (10 or 12mm nut I believe) and it should be totally disconnected. Once you get access to it it's cake, getting the exhaust out of the way is the only labor intensive part
Follow Ups	How much of a pain to replace a starter? - Timmy 15:38:26 08/13/08 It's too tough. (n/m) - Barry (NJ) 15:43:49 08/13/08 2nd. If you have to ask how hard something is then it's too - 600ZXR 15:47:33 08/13/08 wrong wrong wrong. I constantly keep tackeling projets - longhornz32(Fort Worth) 15:56:31 08/13/08 You obviously don't have to ask.Thanks for proving my point. (n/m) - 600ZXR 16:22:40 08/13/08 Um how do you think I determine if a project is too tough - longhornz32(Fort Worth) 18:20:57 08/13/08 Right, you look at it ask yourself what is involved then - 600ZXR 18:49:07 08/13/08 Hmm. So with your reasoning if I know something is wrong - longhornz32(Fort Worth) 20:59:39 08/13/08 I'm glad I didn't follow your reasoning... - rojoloco (San Diego) 04:16:15 08/14/08 You win 600ZXR - Bezza 18:40:08 08/13/08 "and Mr. Wrong" (n/m) - ZXers 19:21:02 08/13/08 doh... *not too tough ;~) (n/m) - Barry (NJ) 15:48:45 08/13/08 Ever removed your exhaust? It's pretty straight forward - 91Z32TT 15:43:51 08/13/08 Note: I may have forgotten a couple bolts - 91Z32TT 15:44:55 08/13/08 I never removed the exhaust when removing the starter. (n/m) - Barry (NJ) 15:47:37 08/13/08 Hmmm, maybe you don't? I seemed to recall my SZ pipes - 91Z32TT 15:52:10 08/13/08 Ok, first off thanks for everyone's help, I need jack stands - Timmy 15:58:37 08/13/08 Starter's not too bad, even for a first time. Just a regula - yobobrox 16:36:00 08/13/08 Geez Tim, you've been here for 9 years. Time to get - Gordo 93TT Daytona 16:26:56 08/13/08 I did have Jackstands but I just moved back home from - Timmy 18:16:53 08/13/08 Rule #1: NEVER sell or give away any tools. (n/m) - WoodmanZ 04:45:24 08/14/08 Re: Rule #2: Buy any tool you 'might' someday need. (n/m) - Gordo 93TT Daytona 16:54:30 08/14/08 One tip, don't forget to disconnect the battery. (n/m) - TTFairladyZ 17:11:25 08/13/08 2nd (n/m) - Piranha(AZ) 17:26:51 08/13/08 it is def a pain. i went to sears and bought a starter wre - pearlyellowtt 18:30:23 08/13/08 ???? I've had no problem removing it with a 14mm wrench - Dave N 18:35:12 08/13/08 crap, we're supposed to rotate that? (n/m) - LJZTT 21:07:55 08/13/08 i think he's referring to an O2 sensor type wrench.. (n/m) - LaRose 21:09:53 08/13/08 lol! - Waggz 21:09:54 08/13/08 "Not needed on the Z." Hence the point of my post. :-) (n/m) - Dave N 21:25:16 08/13/08 ah. - Waggz 21:45:44 08/13/08 Hence why your post just made my night. (n/m) - 5280Z_nightstalker 23:22:08 08/13/08 On a scale of 1 to 10 of difficulty... - Waggz 18:57:18 08/13/08 If your profile is accurate, then you still have the OE - Dave N 19:00:38 08/13/08 Incredibly easy - ZDUCTIV 01:01:41 08/14/08 If you go OEM forking out $317 is going to be the most >> - CincyZX 01:06:59 08/14/08 Not really .. he can look here >>>>> - PLEAZURE in CA (SD) 04:12:13 08/14/08 Why buy a used starter? - CincyZX 22:27:56 08/14/08
Post a Followup	You cannot reply to this message because you are not logged in.