Subject	Get rid of the front mount.
Posted by	Waggz on August 10, 2008 at 8:11 PM
	This message has been viewed 210 times.
In Reply To	overheating with a FMIC!!! posted by red 93 z32 on August 10, 2008 at 08:00 PM
Message	Also check for debris that may be lodged in the condenser and between the condenser and the radiator. Make sure they're no air bubbles in the coolant lines and flush the coolant of its old. Your spal fan may also be the cause if it is too small or has no shroud. Go ahead and get a water pump overdrive pulley and go ahead and get some redline water wetter while you're at it. **SELLING: Mods >> 2.5" test pipes, HKS intercoolers **SELLING: Stock >> driveshaft, 6 stock TT injectors with rail, new style brand new rail, intercoolers, intercooler/intake piping.
Follow Ups	overheating with a FMIC!!! - red 93 z32 20:00:51 08/10/08 change back to SMIC - Pilot.P (NZ) 20:05:09 08/10/08 Re: change back to SMIC - red 93 z32 20:07:17 08/10/08 Better? Enough so you'd rather look at your Z than drive it. - 240Z FeO2 20:23:27 08/10/08 LOL! (n/m) - Dustin 20:30:32 08/10/08 LMAO. Then it can look good in the garage and nothing else. (n/m) - AbsolutZ (OH) 22:05:00 08/10/08 gonna trailer it to the meets to show off it's "cool" looks? - ZLover4Life 23:11:44 08/10/08 Shorter drives, more stops to pose for pics. - Ted (92TT) 00:45:54 08/11/08 Excellent bait, well done! (n/m) - Kenny 01:05:40 08/11/08 oh man... (n/m) - CRAZZEPETE. 14:12:21 08/11/08 2nd, they flow better too. (n/m) - ghostinator (fl) 20:12:11 08/10/08 Sounds to me like you have more problems than - na300zx (OH) 20:07:47 08/10/08 Re: Sounds to me like you have more problems than - red 93 z32 20:10:05 08/10/08 2nd, fan clutch is probably bad (n/m) - spyhunterTT(nj) 05:40:56 08/11/08 I hadn't checked his profile when I posted that - na300zx (OH) 06:23:37 08/11/08 Get rid of the front mount. - Waggz 20:11:34 08/10/08 cops and ricers think they are hot! - DualZ (SF) 20:18:31 08/10/08 LOL. putting fmic on z looks like putting ebay's grill on a - flabz 23:35:41 08/10/08 Get rid of the electric fan and get a HI PULLEY for your - Bernie (NoVA) 20:51:31 08/10/08 may not be the fmic - z32pilot 20:54:24 08/10/08 move to Alaska? (n/m) - LJZTT 21:12:41 08/10/08 ricer (n/m) - zyoulater 21:33:10 08/10/08 the problem is not your FMIC you need to do some research - dream Z (MD) 22:05:03 08/10/08 it may seem obvious..... - vorpalZ 23:06:14 08/10/08 Do you still have the AC system?? - 1badz32 (MN) 23:07:07 08/10/08 HI Pulley, SMICs, & go back to stock fan. Problem solved. (n/m) - Josef(Houston) 23:19:15 08/10/08 first thing I'd do is ditch your electric fan - aliaZ 23:55:30 08/10/08 Seems like your main problem is the fan - Ashman2k2 00:05:35 08/11/08 Oh, and if you still have the AC condensor, make sure to - Ashman2k2 00:08:02 08/11/08 *grabs popcorn. - nemo1080 (Iowa) 00:16:59 08/11/08 Nismo thermostat makes no difference over stock (n/m) - BigTDogg (MA) 17:37:27 08/11/08 opens at a colder temp to allow coolant to flow sooner... - nemo1080 (Iowa) 23:51:33 08/11/08 But it flows the same amount of fluid per minute - BigTDogg (MA) 07:36:57 08/12/08 that is a a good call... - nemo1080 (Iowa) 17:39:47 08/12/08 clean out your AC condenser!!!!!!!!!!!! - Kong ZTT GT28RS MD 06:08:24 08/11/08 if you were here to ask about FMIC's before you put it - CRAZZEPETE. 14:11:22 08/11/08 Check the washer on your radiator cap. You may have to - TT-Z (Cape Coral, FL) 14:57:34 08/11/08 *bookmark for future noobs (n/m) - Alan(MD/NJ) 15:49:15 08/11/08
Post a Followup	You cannot reply to this message because you are not logged in.