Subject	nice
Posted by	Zleepertt(MD) on July 08, 2008 at 7:26 PM
	This message has been viewed 87 times.
In Reply To	Rolling the fenders. posted by Tu on July 08, 2008 at 06:38 PM
Message	I never really knew how fender rolling was done. You did both front and rear fenders, correct? Thanks,
Follow Ups	Rolling the fenders. - Tu 18:38:36 07/08/08 I like the last pic, 10x nicer than a few months ago. (n/m) - sukhi95ttz 18:42:53 07/08/08 Looks good! (n/m) - Dustin 18:44:22 07/08/08 where'd you find the tool? I need to do this bad (n/m) - Crim 19:14:08 07/08/08 http://www.rollyourfender.com/index.html - Tu 19:17:11 07/08/08 nice - Zleepertt(MD) 19:26:29 07/08/08 just the rears were done. fronts were not rubbing. (n/m) - Tu 21:01:44 07/08/08 You've got a little schmultz on the lower fascia in the last - Dave N 19:45:43 07/08/08 *schmutz* - robo (sebring1970) 19:56:44 07/08/08 True, and *schmaltz* is chicken fat and onions. (n/m) - Barry (NJ) 20:48:14 07/08/08 what is that, a paint stripper? (n/m) - robo (sebring1970) 21:19:18 07/08/08 No, it's tasty Eastern European cooking fat ;~) (n/m) - Barry (NJ) 22:08:35 07/08/08 schlitz? (n/m) - BigTDogg (MA) 09:42:35 07/09/08 fixing the cracks..? No idea here. Anyone..? Bueller..? (n/m) - Tu 20:28:07 07/08/08 If the area isn't too visable, just sand it a bit... - Barry (NJ) 20:51:35 07/08/08 Re: If the area isn't too visable, just sand it a bit... - Guapo 21:07:06 07/08/08 I don't think that'll prevent rust ;~) (n/m) - Barry (NJ) 21:09:16 07/08/08 This is texas. What is rust? (n/m) - Guapo 21:14:36 07/08/08 Get out of Dallas every once in a while - 300twinz (satx) 21:43:09 07/08/08 I Do! I was in Arlington just the other day :) (n/m) - Guapo 21:56:10 07/08/08 Nice. While the motor was out last month... - Barry (NJ) 22:06:32 07/08/08 I swear 2+2 T-tops are prone to rusting for some reason - Ashman2k2 00:36:18 07/09/08 Clear nail polish. (n/m) - Bernie (NoVA) 06:36:49 07/09/08 "almost a clean car"? - Luthandrian 21:55:42 07/08/08 That works, but I <3 dremel. (n/m) - Scotts94z32 00:27:40 07/09/08 Just cut them off and sand? (n/m) - BigTDogg (MA) 09:40:22 07/09/08 Yessir. Can't even tell on my car. - Scotts94z32 09:59:53 07/09/08 can you explain what you did? I love to dremel also and if - mogaffar 10:14:25 07/09/08 Hard to describe besides simply saying we used a dremel - Scotts94z32 13:05:50 07/09/08 thanks man, question wouldnt that be more prone to rust? (n/m) - mogaffar 15:10:53 07/09/08 at first glance, that sounds like it would leave a sharp - CRAZZEPETE. 16:09:32 07/09/08 interesting, I think I will have to do this when I install - CRAZZEPETE. 16:08:25 07/09/08
Post a Followup	You cannot reply to this message because you are not logged in.