Subject	You obviously don't know this owner and how lazy he is :) (n/m)
Posted by	Woody75 (Denver) on May 20, 2008 at 1:21 PM
	This message has been viewed 176 times.
In Reply To	well done... One quick thing that I would suggest is.. posted by fantomZ(OH) on May 20, 2008 at 12:21 PM
Message
Follow Ups	Helped a buddy put on his Stillen lower bumper lip. - Woody75 (Denver) 09:19:50 05/20/08 Looks good. Was a heat gun not sufficient for the PCV? (n/m) - Guapo 09:22:45 05/20/08 The torch was sitting there so I used it. - Woody75 (Denver) 09:27:35 05/20/08 fair enough :) (n/m) - Guapo 09:42:14 05/20/08 nice save. looks great (n/m) - Atl300zxTT 09:42:04 05/20/08 Looks great, did you paint it yourself? - JUNz (?00)rwhp 09:42:39 05/20/08 I didn't paint it. Yes on the kwiklift. (n/m) - Woody75 (Denver) 09:43:44 05/20/08 Great job. (n/m) - ENVYMYZ 09:54:29 05/20/08 good as new (n/m) - CRAZZEPETE. 09:58:38 05/20/08 Top-notch work. (n/m) - mlov(NJ) 10:00:18 05/20/08 That car's nasty.. he should sell it (n/m) - bezbefootball 10:01:20 05/20/08 looks pretty good (n/m) - The Devils Z 10:06:11 05/20/08 Awesome work. I wouldn't have thought that so much damage - dregos 10:06:24 05/20/08 Nicely done (n/m) - spicyZ 10:11:38 05/20/08 Looks great (n/m) - Zblackbeast 10:55:38 05/20/08 Looks great - sfpearl300zTT 11:00:17 05/20/08 Clean repair. (n/m) - Bernie (NoVA) 11:02:54 05/20/08 nice repair job. (n/m) - sfarrah 11:43:23 05/20/08 hard to believe it fit so well on that bumper - volcomstone550 12:00:57 05/20/08 No screws really. - Woody75 (Denver) 13:24:14 05/20/08 That looks good, wish I had a buddy that could do that - 300ZMang 12:08:28 05/20/08 Nice...now, he just needs to drive carefully from now on. :) (n/m) - 5150Z 12:13:34 05/20/08 You know, a lot of times it's not the driver... - Z DNA 13:32:46 05/20/08 Impressive! (n/m) - Spongerider :) 12:13:51 05/20/08 well done... One quick thing that I would suggest is.. - fantomZ(OH) 12:21:01 05/20/08 You obviously don't know this owner and how lazy he is :) (n/m) - Woody75 (Denver) 13:21:24 05/20/08 it's cool. Just saw an opportunity for a good - fantomZ(OH) 13:52:30 05/20/08 much better (n/m) - LJZTT 12:26:34 05/20/08 Nice job. (n/m) - TT XTZ 12:28:56 05/20/08 will the tape hold it? or does it need to be molded in? - genic 12:31:01 05/20/08 Of course it holds it, dummy. (n/m) - Kenny 12:39:16 05/20/08 well some two-sided tape doesnt stand up over time - genic 12:44:12 05/20/08 used that same tape on my 90-93 rear spoiler - Tikigod (Denver) 12:56:46 05/20/08 He used 25-angle tape, dummy. (n/m) - Kenny 12:57:21 05/20/08 Never underestimate 3m double sided tape, good stuff. (n/m) - zboost(NoVA) 13:12:02 05/20/08 If it was on my Z I would have used some sort of glue/cement - Woody75 (Denver) 13:27:28 05/20/08 Automotive GOOP works pretty well too - used - jzack 18:53:20 05/20/08 gotcha..thats what i was wondering..tks sir (n/m) - genic 20:12:52 05/20/08 looks much better (n/m) - moxie (SF) 12:56:00 05/20/08 Great job! (n/m) - SeedyROM 13:11:28 05/20/08 Looking good! - Cade(PA) 13:19:08 05/20/08 Very nice job....how do you like the quick lift? - outkaZTT 14:56:08 05/20/08 It works great, but has some drawbacks. - Woody75 (Denver) 15:14:36 05/20/08 are the ceilings in your geerage high enough for a 2 post? (n/m) - genic 20:14:01 05/20/08 yes, if not he can cut into the 2nd floor. :) - zfreak(Denver) 23:15:11 05/20/08 Just high enough for a short 2 post. (n/m) - Woody75 (Denver) 08:38:35 05/21/08 Thanks for the response - outkaZTT 21:02:13 05/20/08 lookin good (n/m) - nemo1080 (Iowa) 15:11:25 05/20/08 Master piece! (n/m) - Turbonium 300Zx 16:59:24 05/20/08 Good job, that looks way better than before. (n/m) - Musashi Sword 17:38:40 05/20/08
Post a Followup	You cannot reply to this message because you are not logged in.