Subject	ah..
Posted by	Waggz on April 06, 2008 at 12:32 PM
	This message has been viewed 222 times.
In Reply To	There beefed up factory pieces (n/m) posted by 550HPTT on April 06, 2008 at 12:25 PM
Message	I remember someone was working on some VTC adjustable cam sprockets. I guess I had those mixed up. ________________________________________________________________________________ |___________________________________*Rebuilding*__________________________________| **"What you did is no different than if I invited you to a big party, you funded some of the beer money, then came over, drank all the beer, asked us to go remove the guy in the bathroom so you could go, and proceeded to take a shit on the living room rug while we were doing it."** Greg (Dallas) 15:10:04 03/09/08
Follow Ups	PSA - rebuilt VTC sprockets hits a major milestone! - LitlElvis 23:23:43 04/05/08 Woohoo! - Broke_as_**** 23:26:21 04/05/08 When are you releasing - ZXRider(SoCal) 23:27:30 04/05/08 I should have the half-moons by June, hope to price ~$20/pr - LitlElvis 23:32:04 04/05/08 Dang - ZXRider(SoCal) 23:34:42 04/05/08 Re: Dang - LitlElvis 23:41:59 04/05/08 Gotcha - ZXRider(SoCal) 23:52:05 04/05/08 You can get block orfices from nissan. (n/m) - Spddracer 06:28:44 04/06/08 How important it is to replace those? - ZXRider(SoCal) 11:32:42 04/06/08 I replaced mine because I don't like to leave a stone - LitlElvis 12:14:41 04/06/08 =) - ZXRider(SoCal) 12:19:13 04/06/08 Yeppers, that's why I made mine removeable... - LitlElvis 12:23:38 04/06/08 2nd, Replaced mine, too - against the thoughts of many. (n/m) - whitepearlz 14:18:20 04/06/08 good idea - aliaZ 22:22:01 04/06/08 Exactly what my machinist said. =) (n/m) - whitepearlz 19:13:53 04/07/08 The ones to worry about are teh check ball orfices - Spddracer 14:37:22 04/06/08 Where are the ones you are describing located at? (n/m) - ZXRider(SoCal) 14:38:14 04/06/08 when I removed the check valves, the balls were rusty - LitlElvis 22:44:32 04/06/08 Are these the adjustable ones? (n/m) - Waggz 01:35:43 04/06/08 No (n/m). (n/m) - chrisq 10:22:21 04/06/08 There beefed up factory pieces (n/m) - 550HPTT 12:25:55 04/06/08 ah.. - Waggz 12:32:45 04/06/08 How much are you going to be asking for them? - Kong ZTT GT28RS MD 02:07:56 04/06/08 Re: How much are you going to be asking for them? - LitlElvis 12:07:31 04/06/08 Very nice, looking forward to the release. (n/m) - RAGTPZ 13:28:57 04/06/08 I have about 3800 noise free miles on my test set - citation 19:11:18 04/06/08 I've got 3200 noise free miles on mine (n/m) - aliaZ 22:12:08 04/06/08
Post a Followup	You cannot reply to this message because you are not logged in.