Subject	Looks like you know what to do now. Here is some more info.
Posted by	DVDBURN (MD) on March 17, 2008 at 7:06 PM
	This message has been viewed 64 times.
In Reply To	My Dyno Sheets, and an Auto-Trans Dyno procedure question... posted by Barry (NJ) on March 17, 2008 at 10:23 AM
Message	Online FSM drawing showing the lockup solenoid. [ http://300zx-twinturbo.com/cgi-bin/manual.cgi?list=at&dir=&config=&refresh=&direction=forward&scale=0&cycle=off&slide=41&design=default&total=194 ] Gregs post regarding it. (which I see you read) [ http://www.twinturbo.net/net/viewmsg.aspx?forum=general&msg_id=1124288 ] My post regarding it. [ http://www.twinturbo.net/net/viewmsg.aspx?forum=general&msg_id=1682547 ]
Follow Ups	My Dyno Sheets, and an Auto-Trans Dyno procedure question... - Barry (NJ) 10:23:58 03/17/08 Barry trust me on this...get rid of the auto tranny - 300twinz (satx) 10:30:10 03/17/08 Bah! That doesn't answer my question :-p (n/m) - Barry (NJ) 10:31:38 03/17/08 He's starting to cave...trust me on this one. (n/m) - Eric(NJ) 10:43:53 03/17/08 automatics rock!!! - phillyz 08:00:07 03/18/08 Well Tony just gave me a call, I forget his SN... - Barry (NJ) 10:53:32 03/17/08 Yep, sounds like what I've done in the past - SeedyROM 11:55:28 03/17/08 Do as I say not as I do? :-P (n/m) - BigTDogg (MA) 12:04:59 03/17/08 Words to live by ;) (n/m) - SeedyROM 12:15:00 03/17/08 Nice S2000! - BradZ (FL) 10:56:22 03/17/08 hahaha We should have bought it! (n/m) - Irocsx2002 11:30:02 03/17/08 Congrats on the numbers buddy...they will only get higher! - Hawkin"Z" 11:16:22 03/17/08 when you get it straightened out - Alan(NJ) 11:21:10 03/17/08 or we can wait til Eric installs his turboback exhaust. (n/m) - Alan(NJ) 11:58:26 03/17/08 Likely, because I'm in no real hurry to dyno again - Barry (NJ) 12:29:45 03/17/08 If either of you wouldn't mind keeping me in that loop, - dogpile 17:08:07 03/17/08 Will do. (n/m) - Barry (NJ) 18:00:15 03/17/08 It's obvious to me that the root of your problem was... - Bernie (NoVA) 13:10:09 03/17/08 lol... <3 U (n/m) - Barry (NJ) 13:39:46 03/17/08 Still laughing... (n/m) - Barry (NJ) 13:43:25 03/17/08 Re: My Dyno Sheets, and an Auto-Trans Dyno procedure questio - WazTTed 18:52:32 03/17/08 Looks like you know what to do now. Here is some more info. - DVDBURN (MD) 19:06:47 03/17/08 Bah. - Dustin 20:09:04 03/17/08 is that boost reading correct? (n/m) - spyhunterTT + 93Vert(nj) 21:21:52 03/17/08 Re: is that boost reading correct?... - Barry (NJ) 22:10:58 03/17/08
Post a Followup	You cannot reply to this message because you are not logged in.