Subject	just get the big chunks of the old stuff off then put the
Posted by	robo (sebring1970) on March 11, 2008 at 9:18 AM
	This message has been viewed 30 times.
In Reply To	taillight tar posted by WE350Z on March 11, 2008 at 12:49 AM
Message	new butyl sealant on top. You're putting goo on top of goo, doesn't matter . . . "Straight-line acceleration is probably the first aspect of automotive performance that any intelligent driver gets bored with." Peter Gregg "We owe a lot to the dragsters. They always break something, figure out a way to beef up the part and the benefit trickles down." Robo "Not everything that can be counted counts. Not everything that counts can be counted." Einstein "And now my friend, the first-a rule of Italian driving, [Franco rips off his rear-view mirror and throws it out of the car] what's-a behind me is not important." Raul Julia, playing Franco Bertollini while driving a Ferrari Daytona in the movie Gumball Rally
Follow Ups	taillight tar - WE350Z 00:49:10 03/11/08 Maybe try "Goo Off"...not sure if it'll damage paint though (n/m) - LoqueZX(CA) 00:52:45 03/11/08 hmm - Insomniac (VA) 00:52:50 03/11/08 on a second note, where do you get "taillight tar"? - SaucyTabasco 02:21:19 03/11/08 Re: on a second note, where do you get "taillight tar"? - Raiders3986 03:57:37 03/11/08 I got mine at my local Oreilly Auto $16 and they gave - jcieslik 08:35:43 03/11/08 I just recently called Coz for some. He got it right out. (n/m) - rojoloco (San Diego) 22:33:18 03/11/08 What do you normally heat it up with? (n/m) - Z_Cherub 10:08:45 03/11/08 the sun - robo (sebring1970) 10:17:37 03/11/08 Key word being "summer". :-P - TT XTZ 10:26:00 03/11/08 Be careful with this technique - spicyZ 10:28:50 03/11/08 yeah, yur right, but like you said below, be just as careful - robo (sebring1970) 10:56:30 03/11/08 Good to know. Thanks, all! (n/m) - Z_Cherub 11:12:55 03/11/08 wow this thread grew... i used hairdryer - WE350Z 12:50:18 03/11/08 also i ended up just scraping down to think layer of goo... (n/m) - WE350Z 12:51:52 03/11/08 the answer to so many questions, "think layer of goo," lol (n/m) - robo (sebring1970) 13:01:54 03/11/08 haha (n/m) - WE350Z 13:29:09 03/11/08 I used a heat gun. Carefully :-) (n/m) - spicyZ 10:29:23 03/11/08 3M tar strips... from your local car parts store. - Multi_Read 08:01:36 03/11/08 No need to remove it all - spicyZ 08:28:09 03/11/08 just get the big chunks of the old stuff off then put the - robo (sebring1970) 09:18:55 03/11/08 I didnt remove 100% of it, so far so good. (n/m) - dpjax 10:28:26 03/11/08 Same here. (n/m) - Turbonium 300Zx 15:37:15 03/11/08 Just get off most of it. - rojoloco (San Diego) 22:35:16 03/11/08
Post a Followup	You cannot reply to this message because you are not logged in.