Subject	What's your thought
Posted by	ZXRider(SoCal) on March 09, 2008 at 3:20 PM
	This message has been viewed 68 times.
In Reply To	Not off the shelf posted by Kyle(Houston) on March 09, 2008 at 03:14 PM
Message	on keeping the stock 87mm bore and re-using the OEM pistons? Basically honing the block and installing new rings on the old pistons? With the crank micropolished and new main, rod bearings installed? That's the route I am heading with my engine and I rather know the problems I might face before I start assembling everything. I have nightmares about that happening...I'd be the poor bastard you'd hear about on the news that gets killed by a softball-size chunk while spreading out my body over the hood and screaming "Nooo!" (Having a conversation about hail damage) - BradZ (FL) on March 25, 2005 at 9:56 PM Tell your friend that you could take a dump, light it on fire and that would be hotter shit than his car. Probes suck, that's just all there is to it. - 300ZXpert (someday) on April 04, 2005 at 11:35 PM P.S. You REALLY are on here at ALL hours! And I thought I was bad! :) - zmenon on August 16, 2005 at 3:06 AM LOL...2+2 drivers should grow mullets..."Business in the front...party in the back" ;) - BradZ (FL) on November 29, 2005 at 4:45 PM
Follow Ups	Weiso pistons and eagle rods - RedTTZ91(OK) 14:37:58 03/09/08 The wiseco piston noise problem has been fixed. - aliaZ 14:42:07 03/09/08 Would you happen to know if Wiseco - ZXRider(SoCal) 14:49:11 03/09/08 2nd (n/m) - THEDUCK 14:50:45 03/09/08 Not off the shelf - Kyle(Houston) 15:14:49 03/09/08 Re: Not off the shelf - RedTTZ91(OK) 15:17:12 03/09/08 I have used the wiseco/eagle combo in cars running 700+ Rwhp (n/m) - Kyle(Houston) 15:22:23 03/09/08 What's your thought - ZXRider(SoCal) 15:20:30 03/09/08 It depends on the shape of you cylinders - Kyle(Houston) 15:24:03 03/09/08 Would I be able to check those - ZXRider(SoCal) 15:27:53 03/09/08 I'd let a machine shop measure that for you - aliaZ 15:34:25 03/09/08 Gotcha - ZXRider(SoCal) 15:44:55 03/09/08 plastigage gives you a ballpark measurement - aliaZ 18:00:37 03/09/08 I see - ZXRider(SoCal) 18:40:17 03/09/08 Are you doing the short block assembly or the machinist? - AZHeat 18:43:26 03/09/08 I'm hoping that I can manage all the assembly - ZXRider(SoCal) 18:53:16 03/09/08 Getting kinda pricey and time consuming there, huh? - apudapus 23:29:46 03/09/08 Would it have been better to go with IPP block, YES - ZXRider(SoCal) 23:55:15 03/09/08 I noticed on eagle rods, there is more big end side - AZHeat 15:02:33 03/09/08 JE pistons or weiscos? - RedTTZ91(OK) 15:29:50 03/09/08 I'd get the wisecos and spend the money you saved - aliaZ 15:36:15 03/09/08 Its getting tuned regardless. - RedTTZ91(OK) 15:37:30 03/09/08 I wasn't able to notice any difference in oil pressure - aliaZ 15:31:17 03/09/08 any other recommendations - RedTTZ91(OK) 15:40:48 03/09/08
Post a Followup	You cannot reply to this message because you are not logged in.