Subject	Seriously? No... goto a MacHine shop!
Posted by	Adam A. on February 28, 2008 at 8:10 AM
	This message has been viewed 41 times.
In Reply To	You should do this... posted by icsamerica on February 27, 2008 at 11:32 PM
Message	Perhaps this is how it's done in back of the garage before we invented the money tree, but when we have the tools available and are kind of turned off by wasting money... My opinion is that you would not be able to get it round, creating a perfect situation for the bearing the fail again. It is the most important part of your car (next to the tires, and the brakes, and the steering wheel... ok so it's all important); but don't skimp on the rebuild or you will regret it when it's time to rebuild it again.
Follow Ups	Rod Bearing Failure on TT engine I am going to Rebuild - Viper498 ( MO ) 17:58:28 02/27/08 Rebello is offering 10, 20 & 30 + bearing for our TT's - Izzy 19:23:46 02/27/08 Get a good used crank? (n/m) - ZXRider(SoCal) 19:31:51 02/27/08 I got one for sale. $160 shipped. - na300zx (OH) 19:41:35 02/27/08 I may take you up on that. It would cost a lot to ship - Viper498 ( MO ) 21:15:22 02/27/08 If you want i have some rods and pistons i could send you. (n/m) - Sleeper_TTZ(SeKy) 00:49:44 02/28/08 I figured it owuld be ~$40 or $50 for shipping - na300zx (OH) 07:22:06 02/28/08 Get a good used one. ur current one will most likely need to - MikeVar82 20:38:05 02/27/08 Why isn't it good to re-cut. As lond as its not more than... - Sleeper_TTZ(SeKy) 00:48:32 02/28/08 The Connnecting Rod is also scored on that particular - Viper498 ( MO ) 21:13:02 02/27/08 Does anyone know? (n/m) - Viper498 ( MO ) 22:49:47 02/27/08 Any stock con-rod will do. just re-number it. (n/m) - LitlElvis 23:32:54 02/27/08 Sweet, thanks for the response. (n/m) - Viper498 ( MO ) 23:35:13 02/27/08 You should do this... - icsamerica 23:32:29 02/27/08 Wow, I wasn't sure if I could do that. I went out to the - Viper498 ( MO ) 23:38:30 02/27/08 I'll try this on the con-rod as well. (n/m) - Viper498 ( MO ) 23:39:27 02/27/08 You could take it to a shop and they can tell you if its... - Sleeper_TTZ(SeKy) 00:46:57 02/28/08 Seriously? No... goto a MacHine shop! - Adam A. 08:10:27 02/28/08 It's not rocket science and can be do by anyone of us... - icsamerica 10:05:25 02/28/08 Does the damage in the pictures on my main post - Viper498 ( MO ) 00:23:39 02/28/08 Re: Rod Bearing Failure on TT engine I am going to Rebuild - dirtbiker194 00:36:13 02/28/08 I had same thing happen - Daniel(CA) 19:02:14 02/28/08
Post a Followup	You cannot reply to this message because you are not logged in.