Subject	Will do...I'm actually using the nylon threaded hose
Posted by	collegeboy on February 26, 2008 at 11:37 PM
	This message has been viewed 47 times.
In Reply To	Use a dremel cutting wheel, much easier. Also use posted by AZHeat on February 26, 2008 at 11:08 PM
Message	instead of the stainless threaded hose. I actually never heard of this stuff before, but it comes with SPL's Radiator/Oil Cooler kit and I was impressed with it when I got that kit. I decided to go with it for my fuel lines cause I figure it is basically just as strong and can hold the same pressure (it can obviously hold over 100psi of oil pressure), but it can also rub on paint for example without being harmed OR harming the other surface. I also figured it would be easier to assemble than the SS braided line is (no poked fingers)...I guess I shall see now. Thanks for the tips. I really appreciate it. Let the late night begin! I got roughly 40' of this hose and a TON of fittings so I'll be seeing the sun rise =) Thanks, Mike 1991 Black 3.0 Twin Turbo 1991 Black NSX 3.5 Supercharged 98 Mazda Truck 03 Dodge 2500 Truck La-Z-Link ^^Hard engine break in method^^ La-Z-Link ^^MY FACEBOOK...CHECK IT OUT^^ La-Z-Link ^^MY MYSPACE (not on there very much), BUT STILL...CHECK IT OUT^^ ---Me: You bought a Porsche? ---sfpearl300z: lol, no no, I have a decent sized penis so no need for that "you can't even BORROW balls. I guess you just get used to your tail being between your legs? Better than having nothing there, huh?" ~ Spee tough talking someone online "felt wierd fingering my exhuast for 1hr with no results :(" - zboost "lmao, i know, theres more drama and favoritism on tt.net than a middle school girls locker room" - sfpearl300z "I think I'll pass on giving my car a handjob" - joel(PA) "I did plug the holes, But I did it by taping over them a lot, I didnt think that maybe HOT air is comming through there, And it melted the tape, damnit im an ass." - DC 21
Follow Ups	Any good site out there with some AN fitting instructions? - collegeboy 22:25:48 02/26/08 Did you get yourself an aluminum vise teeth to hold - AZHeat 22:27:09 02/26/08 Already got one (n/m) - collegeboy 23:03:40 02/26/08 Male threads fit into the female threads. YMMV, however. (n/m) - Guapo 22:40:14 02/26/08 Heck yes! Perfect! - collegeboy 23:06:35 02/26/08 Use a dremel cutting wheel, much easier. Also use - AZHeat 23:08:58 02/26/08 Will do...I'm actually using the nylon threaded hose - collegeboy 23:37:04 02/26/08 use a cut off wheel, cleanest and ,easiest by far (n/m) - sparkie 23:22:34 02/26/08 Yes, wash the inside out afterwards though. (n/m) - RSR 07:57:28 02/27/08 Just cut through the steel braid with the cut off wheel - sparkie 08:41:15 02/27/08 Bookmarked, thanks! (n/m) - 91300zxttkid 23:24:24 02/26/08 ROFLMAO @ step 6 - Broke_as_**** 02:32:44 02/27/08 For those that have ever been worried... - collegeboy 02:36:30 02/27/08 To be fair, - RSR 07:58:37 02/27/08 2nd (n/m) - aliaZ 08:28:27 02/27/08 i recently posted some pic on my FAQ accusump install (n/m) - sawbonez 07:19:00 02/27/08
Post a Followup	You cannot reply to this message because you are not logged in.