Subject	even after a year of daily driving it....
Posted by	zboost(NoVA) on February 18, 2008 at 4:48 AM
	This message has been viewed 63 times.
In Reply To	Can you elaborate on the CC clutch and its driveability posted by Kong ZTT GT28RS MD on February 18, 2008 at 01:19 AM
Message	I stalled it at least 3 times a week..... I was paranoid about hills because it was hard to take off. a bit of an on/off switch.... I dunno, maybe I had a defective unit, but it was previously rebuilt by the guy I bought it from so I doubt it. that combined with the noise it made (due it being non-sprung which sucks) killed it for me. But that clutch can hold more power. Pedal pressure was the same as with the dxd-fx. BEST 1/4mile 11.92 @ 117mph. PUMP gas, true 11 sec. street car :) (VGTT set-up) stock turbos/injectors "yo yo. writing this one in jail - tight300zx" I hope you got soap on a rope?? (n/m) - Spongerider :) 19:14:08 04/01/04 we'll know if the screen name changes ;) (n/m) - SactoTodd 19:32:36 04/01/04 "I did plug the holes, But I did it by taping over them a lot, I didnt think that maybe HOT air is comming through there, And it melted the tape, damnit im an ass." - - DC 21:11:01 02/18/04 (the "holes" were located on the exhaust)
Follow Ups	Looks like someone else is catching on to the new - Spddracer 15:15:26 02/17/08 They say immitation is the best form of flattery. :) (n/m) - Gold Z 15:34:56 02/17/08 AMS will have a same one coming out soon!!! lol (n/m) - zyoulater 15:37:49 02/17/08 those freakin bastards! - inf 15:39:48 02/17/08 Did you design that pressure plate? (n/m) - collegeboy 15:40:00 02/17/08 Nope.. - Spddracer 16:07:34 02/17/08 Clamping load vs. bearing wear - lazer(AK) 17:24:22 02/17/08 excellent point >> - ztunerz 17:55:31 02/17/08 yep (n/m) - aliaZ 21:16:29 02/17/08 This pressure plate has a higher pivot ratio VS the old - Spddracer 18:23:14 02/17/08 I could see how higher pivot point reduces the amount - AZHeat 18:39:57 02/17/08 Clamp load is only applied to the disk itself, Not the crank - Spddracer 18:44:54 02/17/08 This is correct........ - Greg D. (Specialty-Z) 19:15:36 02/17/08 I don't know about that. The pivot point or fulcrum - AZHeat 19:54:13 02/17/08 Your looking at it wrong I think....... - Greg D. (Specialty-Z) 20:05:25 02/17/08 remember the pressure comes from compressing - Greg D. (Specialty-Z) 20:24:21 02/17/08 Gotcha, makes sense now. - AZHeat 20:30:28 02/17/08 You would not want to use a 4000 LBS clamp load..... - Greg D. (Specialty-Z) 18:24:14 02/17/08 No doubt there. - Spddracer 18:36:36 02/17/08 Who is "we"?Do you work for SouthBend or help in the design? (n/m) - Kyle(Houston) 20:02:29 02/17/08 Not sure what your getting at. - Spddracer 21:35:37 02/17/08 thanks for clearing it up - ArubaDave 12:33:36 02/18/08 RPS has been using that pressure plate in the Carbon Carbon - Greg D. (Specialty-Z) 18:18:14 02/17/08 Mitsubishi what? (n/m) - Spddracer 18:19:35 02/17/08 I would have to ask RPS. I do remember him telling me it was - Greg D. (Specialty-Z) 18:41:45 02/17/08 Doesn't look the same. Did they change later? - DVDBURN (MD) 18:38:36 02/17/08 That is a generic picture of the Carbon..... - Greg D. (Specialty-Z) 18:43:08 02/17/08 Ah... - DVDBURN (MD) 18:46:12 02/17/08 Our plate is not a Mitsu pressure plate. (n/m) - Spddracer 18:43:21 02/17/08 Sure looks just like the plate RPS uses in the Z Carbon (n/m) - Greg D. (Specialty-Z) 18:45:54 02/17/08 Could be, No idea what RPS uses in that kit. - Spddracer 18:51:43 02/17/08 I hope not! - Greg D. (Specialty-Z) 18:53:59 02/17/08 I thought you just said you used this same plate - Spddracer 19:03:23 02/17/08 Southbend plate does look like the Carbon plate... - Greg D. (Specialty-Z) 19:07:54 02/17/08 And maybe RPS did not use it because of its cost. - Spddracer 19:27:21 02/17/08 wrong...... - Greg D. (Specialty-Z) 19:40:38 02/17/08 Is the Carbon carbon a push release or pull release type? (n/m) - AZHeat 18:42:16 02/17/08 Push (n/m) - Greg D. (Specialty-Z) 18:44:01 02/17/08 dxd-fx ftw! (n/m) - zboost(NoVA) 20:03:55 02/17/08 Lol, Like the clutch I take it? (n/m) - Spddracer 21:37:10 02/17/08 I am anal about clutches, but this my friend is amazing - zboost(NoVA) 21:55:51 02/17/08 Can you elaborate on the CC clutch and its driveability - Kong ZTT GT28RS MD 01:19:59 02/18/08 even after a year of daily driving it.... - zboost(NoVA) 04:48:17 02/18/08 as soon as i get my economic stimulus check from the fed, - slayer fan 21:48:06 02/17/08 i need a feramix 2 (n/m) - ZiNnYc 23:04:50 02/17/08
Post a Followup	You cannot reply to this message because you are not logged in.