Subject	Can't a not so expensive consult setup log oil pressure?
Posted by	Bezza on February 11, 2008 at 7:21 PM
	This message has been viewed 46 times.
In Reply To	Unless SZ has one , I don't think they are going to posted by AZHeat on February 11, 2008 at 06:42 PM
Message	I think you can log oil pressure and RPM using a consult type software setup. I haven't done it but perhaps someone else could chime in here. Here is a post where it is alluded to: [ http://www.twinturbo.net/net/viewmsg.aspx?forum=general&msg_id=961396 ] The G force logging would be nice but just the oil pressure and RPM data would convince me if it was a good driver with sticky tires.
Follow Ups	oil starvation question - z32pilot 15:21:32 02/11/08 Wait, what's your question? - Scotts94z32 15:51:19 02/11/08 are you running accusump ?? - z32pilot 15:58:44 02/11/08 No, but I have a Specialty Z custom oil pan. - Scotts94z32 16:38:24 02/11/08 Where did you mount your sump? - Mike(La Canada) 16:27:52 02/11/08 Not sure... - Z_Cherub 15:52:28 02/11/08 Do not put an "extra quart or two" in the pan - 550HPTT 15:53:39 02/11/08 Re: oil starvation question - BobbyT 15:57:56 02/11/08 read this thread - aliaZ 16:14:12 02/11/08 i dont wanna starve my engine from oil! so what are - shougun 12:40:05 02/12/08 don't run race tires (n/m) - aliaZ 15:06:58 02/12/08 Get a SZ oil pan. They are available now and proven. - AZHeat 16:18:00 02/11/08 do you need another core ?? - z32pilot 16:23:16 02/11/08 I have two extra ones already. (n/m) - AZHeat 16:25:55 02/11/08 thanks for the info !! (n/m) - z32pilot 16:28:33 02/11/08 lol (n/m) - PennStateZ (VA) 19:10:35 02/11/08 nitpick - Bezza 16:41:34 02/11/08 indeed (n/m) - aliaZ 16:43:26 02/11/08 Tu has one. I am sure he will test it. He road races. (n/m) - AZHeat 18:20:52 02/11/08 how can he test it without datalogging his oil pressure? - aliaZ 18:33:39 02/11/08 How expensive is the hardware for that? (n/m) - AZHeat 18:35:13 02/11/08 Ask someone who designs oil pans... they'd probably know. (n/m) - PennStateZ (VA) 18:40:24 02/11/08 Unless SZ has one , I don't think they are going to - AZHeat 18:42:24 02/11/08 Can't a not so expensive consult setup log oil pressure? - Bezza 19:21:49 02/11/08 Zing! (n/m) - CaliguyPurdue (redesigning) 20:17:43 02/11/08 I could put it together for between $150 to $1500... - CaliguyPurdue (redesigning) 20:17:21 02/11/08 No doubt you could spend alot - Bezza 20:23:45 02/11/08 Answer inside... - CaliguyPurdue (redesigning) 20:37:02 02/11/08 Thanks for the insight. - Bezza 21:47:23 02/11/08 You should be ok with that setup - CaliguyPurdue (redesigning) 00:00:38 02/12/08 Cool links thanks. - Bezza 00:21:51 02/12/08 By the way - Bezza 22:40:08 02/11/08 Excellent question... - CaliguyPurdue (redesigning) 23:40:35 02/11/08 Damn, I just got my bearings coated at Polydyn too:) - Bezza 00:20:32 02/12/08 where did you get your parts coated? - aliaZ 07:51:12 02/12/08 I coated the bearings myself... - CaliguyPurdue (redesigning) 12:24:13 02/12/08 thanks for the info Jim (n/m) - aliaZ 15:05:58 02/12/08 Do you think one could record oil pressure through the Defi - Scotts94z32 09:41:18 02/12/08 Re: oil starvation question - Izzy 17:45:00 02/11/08 I would like to hear fomr greg/seb, or mike (AZheat) - Rickytl (ma) 22:03:49 02/11/08 Is your engine already out? Other than pulling - AZHeat 22:08:29 02/11/08 Re: Is your engine already out? Other than pulling - Rickytl (ma) 22:19:07 02/11/08 it's not bad .. just did mine recently (n/m) - zxtuner161 15:33:36 02/12/08
Post a Followup	You cannot reply to this message because you are not logged in.