Subject	I use titanium bolts on anything that spins
Posted by	collegeboy on January 30, 2008 at 7:58 PM
	This message has been viewed 49 times.
In Reply To	not sure about the zi posted by gt300zxtt on January 30, 2008 at 06:33 PM
Message	Flywheel bolts, clutch, and differential. I was going to change those out to stainless like the other bolts in my car, but I figured the slight weight savings might make some bit of difference with those since it's rotational mass, especially the clutch pressure plate bolts since they are on the outer edge of the pressure plate. They also don't corrode which is nice. Some might think it's a little retarded, but to me they were worthy purchases. For any other people interested, these are who I bought them from. La-Z-Link Thanks, Mike 1991 Black 3.0 Twin Turbo 1991 Black NSX 3.5 Supercharged 98 Mazda Truck 03 Dodge 2500 Truck La-Z-Link ^^Hard engine break in method^^ La-Z-Link ^^MY FACEBOOK...CHECK IT OUT^^ La-Z-Link ^^MY MYSPACE (not on there very much), BUT STILL...CHECK IT OUT^^ ---Me: You bought a Porsche? ---sfpearl300z: lol, no no, I have a decent sized penis so no need for that "you can't even BORROW balls. I guess you just get used to your tail being between your legs? Better than having nothing there, huh?" ~ Spee tough talking someone online "felt wierd fingering my exhuast for 1hr with no results :(" - zboost "lmao, i know, theres more drama and favoritism on tt.net than a middle school girls locker room" - sfpearl300z "I think I'll pass on giving my car a handjob" - joel(PA) "I did plug the holes, But I did it by taping over them a lot, I didnt think that maybe HOT air is comming through there, And it melted the tape, damnit im an ass." - DC 21
Follow Ups	Has anyone tried recoating their 10mm bolts with zinc or - Jkova300z 17:41:22 01/30/08 eastwood.com - gt300zxtt 18:03:17 01/30/08 cool, do you think there is any risk of it wearing off from - Jkova300z 18:08:57 01/30/08 not sure about the zi - gt300zxtt 18:33:19 01/30/08 I use titanium bolts on anything that spins - collegeboy 19:58:51 01/30/08 you are a richer man than i.... (n/m) - gt300zxtt 20:10:25 01/30/08 Doubt it.....I'm just dumber =) (n/m) - collegeboy 20:16:25 01/30/08 Re: I use titanium bolts on anything that spins - derekinthez 23:15:48 01/30/08 i don't see prices on there. - apudapus 11:26:53 01/31/08 I just purchased some POR-15. - zQuikonE 18:11:28 01/30/08 becareful when using it on body panels and whatnot - spyhunterTT(nj) 18:13:55 01/30/08 I plan to use it on some rusted spots under the car - zQuikonE 18:23:41 01/30/08 I replaced all the bolts in my car with stainless ones - collegeboy 18:37:59 01/30/08 where did you get them from, i can only find ones that dont - Jkova300z 19:18:08 01/30/08 You most likely have a FASTENAL company near by.. - Kong ZTT GT28RS MD 19:42:29 01/30/08 ps.. You should use some anti-seize on the threads.. - Kong ZTT GT28RS MD 00:45:47 01/31/08 Denton Bolt Company right by my house - collegeboy 19:51:47 01/30/08 local hardware stores - gt300zxtt 19:58:09 01/30/08 all? (n/m) - SactoTodd 20:43:16 01/30/08 Yup...pretty much everyone I could get to. - collegeboy 08:37:08 01/31/08 Do not use stainless on stressed bolts - zorpman1 09:38:05 01/31/08 also... SS is approximately the equivelent of Grade "5" bolt - Kong ZTT GT28RS MD 00:36:50 02/01/08
Post a Followup	You cannot reply to this message because you are not logged in.