Subject	the break-down
Posted by	dewey on January 23, 2008 at 11:13 PM
	This message has been viewed 92 times.
In Reply To	well, the correct answer is posted by dewey on January 23, 2008 at 09:04 PM
Message	Note: for comparison purposes, price in (xx) is from Courtesy labor $1140 shop supplies $75 Parts: fuel filter 23.09 (12.50) valve cover gasket x2 38.00 (32) Plenum gasket 9.70 (8.40) Bulk HP fuel hose 68.25 (43) The fuel hose charge just kills me. The bulk cost is $43 for 130" (10ft+) length from Courtesy. The car probably uses 3-4ft length of hose max, and they charge $68!!! I would like to know what the $75 shop supplies are for. Looking back at an old bill for clutch replace, they charge the same amount. I wish some TV reporter would find out if these charges are legit... Anyway, thanks again for letting me vent!
Follow Ups	Let's play "guess how much the dealer charge" game - dewey 19:28:54 01/23/08 Re: Let's play "guess how much the dealer charge" game - dewey 19:31:24 01/23/08 Re: Re: Let's play "guess how much the dealer charge" game - giZmo96 20:27:31 01/23/08 well, the correct answer is - dewey 21:04:07 01/23/08 dang son, you got raped (n/m) - aliaZ 22:23:51 01/23/08 Damn, i would rather get a new set of wheels for that price (n/m) - Josef(Houston) 22:26:16 01/23/08 Why didn't you go to Z1? (n/m) - ali300zx 22:26:54 01/23/08 because.... - dewey 22:47:59 01/23/08 $475 to replace clutch master and slave cylinder? - TTFairladyZ 23:40:56 01/23/08 yikes, great caesar's ghost! - Ahmed 22:32:35 01/23/08 the break-down - dewey 23:13:19 01/23/08 You sure that fuel hose is the correct high pressure fuel - Guapo 23:20:50 01/23/08 Local dealer around me used to sell it by the inch but not - doug8867 07:29:17 01/24/08 I'd rather pay $43 for 10' than $1.55/inch for fuel hose (n/m) - Guapo 09:00:43 01/24/08 That's what your wife said :) (n/m) - AZHeat 13:27:44 01/24/08 What? (n/m) - Kenny 13:39:08 01/24/08 Fuel Injector hose is pricey - collegeboy 00:22:38 01/24/08 Good God! - collegeboy 00:20:10 01/24/08 Re: well, the correct answer is - ouikikazz 14:40:30 01/24/08 $2,000. (n/m) - doug8867 20:05:35 01/23/08 Agreed. (n/m) - Bernie (NoVA) 08:28:47 01/24/08 2nd, b/c thats what they were gonna charge me just for - 96TwinTurboZ 20:55:43 01/24/08 Labor + parts = $800 (my guess) (n/m) - jzack 20:05:46 01/23/08 $613.29 (n/m) - Cyclone510 23:22:40 01/23/08 Did you get an estimate first so you knew what to expect or - 94Z32XTT 01:36:37 01/24/08 Re: Did you get an estimate first so you knew what to expect - dewey 13:49:29 01/24/08 Well as long as you knew and expected it, then there's no - 94Z32XTT 14:41:54 01/24/08 Question... - ZX 2B U 07:56:47 01/24/08 Re: Question... - dewey 13:47:56 01/24/08 you should have known better - ZEngineer 08:07:32 01/24/08 I can't believe how much - alhickabee 08:52:53 01/24/08 it might seem expensive at a first glance - ZEngineer 08:57:46 01/24/08 most people don't get it... - scottyfender 12:33:09 01/24/08 Re: most people don't get it... - dewey 13:53:23 01/24/08 Re: you should have known better - dewey 13:56:48 01/24/08
Post a Followup	You cannot reply to this message because you are not logged in.