Subject	patent pending mofo!!!
Posted by	Broke_as_**** on January 15, 2008 at 3:22 AM
	This message has been viewed 57 times.
In Reply To	dang, that's nice. posted by apudapus on January 15, 2008 at 02:41 AM
Message	The material has to be around 2" wide on each side so it has enough room to fit over the ECU and still reach that bolt hole you can see there. I had to cut the side of the bracket that went down the side of the ecu down to about an 1" wide and of course notch the end to fit over where it mounts to the stock bracket. The bolt hole on top just goes through the new bracket but the bolt on the bottom also goes through wood cover.
Follow Ups	Harness extensions- I was looking at this so I don't hack - ThunderZ 22:54:56 01/14/08 AFter I wrestled with mine, there was no way I was taking - zgene4 22:59:27 01/14/08 Sounds like it was a tough install. Were you able to at - ThunderZ 23:09:48 01/14/08 Not tough, just not stock. Yes, I was able to fit - zgene4 23:27:42 01/14/08 I just made some brackets and moved it to the other side - Broke_as_**** 02:16:14 01/15/08 dang, that's nice. - apudapus 02:41:22 01/15/08 patent pending mofo!!! - Broke_as_**** 03:22:32 01/15/08 i'm planning on bending some sheet metal to make the bends. - apudapus 11:52:47 01/15/08 Very nice. (n/m) - Bernie (NoVA) 02:56:17 01/15/08 I did the same but just used velcro. (n/m) - Woody75 (Denver) 08:17:10 01/15/08 Where are these harness extensions available for purchase? (n/m) - Barry'z (NJ) 15:10:29 01/15/08 Didn't make the group buy? - Broke_as_**** 15:35:50 01/15/08 Thanks! (n/m) - Barry'z (NJ) 18:38:02 01/15/08 for mine, i bolted the ECU towards the right side... - apudapus 02:39:07 01/15/08 Nice job on the harness conversion - I'll likely need - Bernie (NoVA) 02:58:19 01/15/08 Whoa, just a bit of work in that one eh? (n/m) - Broke_as_**** 03:05:23 01/15/08 Nice job on that wireing! looks like a nice project haha (n/m) - 91300zxttkid 05:51:14 01/15/08 Nice work dude! (n/m) - Turnerscasa (Dallas) 05:57:01 01/15/08 Re: for mine, i bolted the ECU towards the right side... - WazTTed 06:40:30 01/15/08 That's how I did mine too. Nice conversion harness! (n/m) - Dallas DamonZ 07:11:50 01/15/08 nice work, how you know how to do that stuff is beyond me... - Craig300ZX 10:43:56 01/15/08 That harness looks familiar - ZXRider(SoCal) 11:01:22 01/15/08 i just realized that i don't have an extra ECU - apudapus 12:07:05 01/15/08 thanks for the kind words, everyone. - apudapus 12:09:55 01/15/08 Thanks guys, this answered my question. (n/m) - ThunderZ 07:30:13 01/15/08
Post a Followup	You cannot reply to this message because you are not logged in.