Subject	yep.
Posted by	Dallas DamonZ on January 14, 2008 at 11:02 PM
	This message has been viewed 35 times.
In Reply To	I think the problem would be sourcing all of the connectors posted by aliaZ on January 14, 2008 at 09:34 PM
Message	very expensive to get repros. At least some of the connectors are common (square injector connectors) and can be had from Amphenol or someone like that. ECU and some of the others.... good luck. Later "If A equals success, then the formula is: A = X + Y + Z, X is work. Y is play. Z is keep your mouth shut." - Albert Einstein When was the last time you *really* did something with your Z to call yourself a Z enthusiast? Member #1 PETZ
Follow Ups	Z32 Parts Time Capsule - dpjax 20:53:08 01/14/08 harness. (n/m) - Halo Z 20:56:13 01/14/08 I figure someone will make a replica whenever those are - ZEngineer 20:59:24 01/14/08 I've thought about doing it - ZLover4Life 21:10:02 01/14/08 charge 150 bucks and I'll buy one. (n/m) - BannonZ 21:11:13 01/14/08 I think the problem would be sourcing all of the connectors - aliaZ 21:34:12 01/14/08 yep. - Dallas DamonZ 23:02:56 01/14/08 If it came down to that - RSR 07:57:56 01/15/08 ? - Dallas DamonZ 08:34:24 01/15/08 ... - RSR 08:55:26 01/15/08 ... - RSR 08:59:01 01/15/08 yep. That's what scares me. (n/m) - Dallas DamonZ 09:55:03 01/15/08 when that happens... - ZLover4Life 21:06:29 01/15/08 "SR20 ricers" :finger: (n/m) - Halo Z 21:10:18 01/14/08 Redundancy Department of Repeatition (n/m) - Keaner 21:15:42 01/14/08 $10 says he takes exisiting harness sections and extends - Bernie (NoVA) 01:29:54 01/15/08 engine (n/m) - inf 20:58:10 01/14/08 Re: Z32 Parts Time Capsule - ZED2 20:59:44 01/14/08 wheel bearings (n/m) - 300zdett(houston tx) 21:08:05 01/14/08 Big 2nd! - monty31 21:11:06 01/14/08 I've been paranoid about my bearings going bad - ZEngineer 21:13:03 01/14/08 harness, wheel bearings, a proven good low miles motor - nemo1080 21:12:35 01/14/08 Un-cut Ti Keys. (n/m) - bstyleZ 21:23:35 01/14/08 60U filters. (n/m) - SkiFly01 21:25:07 01/14/08 Bernie already did that. (n/m) - BlackholeZ 21:42:22 01/14/08 Think it's a little late for that - Broke_as_**** 22:05:38 01/14/08 Real JSPEC Tail Lights (n/m) - 91300zxttkid 21:26:58 01/14/08 Re: Z32 Parts Time Capsule - 90AztecTT 21:27:21 01/14/08 if i could go into a time capsule, i would - Alan(NJ) 21:49:43 01/14/08 I wouldn't, because i couldn't be able to afford it. (n/m) - ali300zx 22:51:11 01/14/08 2nd (n/m) - nemo1080 01:34:04 01/15/08 Suede door panels and OEM "Z" floor mats - AbsolutZ (OH) 21:45:49 01/14/08 Just bought another set - TriniTT 00:20:51 01/15/08 wiring harness, interior trim,door jamb & t-top weatherstrip (n/m) - doug8867 21:53:30 01/14/08 Application specific electronics - Broke_as_**** 22:01:45 01/14/08 a flying Z, with 1.1 GW flux cap. (n/m) - vorpalZ 22:04:46 01/14/08 you are .11 GW short... - scottyfender 22:47:02 01/14/08 the most obvious. GASOLINE!!!!!!!!!!!!!!!!!!! - volcomstone550 22:09:08 01/14/08 I have a blank titanium key, a spare set of the "300ZX" - Only1Z 23:07:53 01/14/08 all moldings and weatherstripping, hood cowlings, - gt300zxtt 00:53:00 01/15/08 ooo, i like this answer. i will have the same. (n/m) - apudapus 02:21:10 01/15/08 Ditto. - Adam A. 08:56:11 01/15/08 Re: Z32 Parts Time Capsule - 90AztecTT 06:56:14 01/15/08
Post a Followup	You cannot reply to this message because you are not logged in.