Subject	I have a similar setup as your you...
Posted by	VECTOR on December 03, 2007 at 10:24 AM
	This message has been viewed 92 times.
In Reply To	What is wrong with our bearings?? made inside.... posted by bubuche on December 03, 2007 at 02:36 AM
Message	Bonjour, I've run the several road racing events with my TD05's too temps ranging from 45degC Willow Springs to 5deg C at ButtonWillow. Car/bearings held up fine. I was using race gas however. Regular octane even the 98Ron in the EU might not be enough to sustain high boost for long. Check your plugs for signs of detonation. PS: Did you notice any differences bwt stock and the nismo crankshaft? PSS: Has your pass side manifold cracked yet? :)
Follow Ups	What is wrong with our bearings?? made inside.... - bubuche 02:36:09 12/03/07 How many miles did you get after the build? - Devi13 04:00:23 12/03/07 you live in France. (n/m) - Eishozzzz 04:11:02 12/03/07 Sorry to hear it. - Bezza 05:14:27 12/03/07 If you were detonating then you might have - RSR 07:14:10 12/03/07 What type of fuel were you using? (n/m) - RAGTPZ 07:27:30 12/03/07 Wrong size bearing. Most likely the case. (n/m) - luke21 07:29:18 12/03/07 Should have tuned the car & turned the boost down. (n/m) - Bernie (NoVA) 07:30:03 12/03/07 >>> - ztunerz 07:43:23 12/03/07 I built up the engine myself. - bubuche 08:12:03 12/03/07 If you tune your car by ear and wait to *hear the detonation - whitepearlz 08:35:04 12/03/07 on high hp Z's especially on in road racing - ztunerz 08:54:27 12/03/07 road and track racing too ;) - bubuche 10:22:44 12/03/07 I have a similar setup as your you... - VECTOR 10:24:21 12/03/07 Road racing with high G turns , braking, acceleration - AZHeat 10:58:30 12/03/07 That's what I was thinking. Oil starvation due to high G's - Gordo 93TT Daytona 11:20:28 12/03/07 The crank counterweight should never slosh in - AZHeat 12:22:56 12/03/07 Maybe I was thinking about my Dad's Model A?? (n/m) - Gordo 93TT Daytona 13:52:08 12/03/07 I have seen old old engines have a oil scoop on the - AZHeat 13:56:56 12/03/07 yep...about 50+ years ago (n/m) - aliaZ 13:58:48 12/03/07 We all learn something new everyday. I was thinking about - Gordo 93TT Daytona 14:46:50 12/03/07 The crackcase in wet sup system is not a vacuum. The - AZHeat 15:44:52 12/03/07 Have you progressed further on your prototype pan? (n/m) - Gordo 93TT Daytona 16:51:55 12/03/07 Yes. Doing the final install on my car in a few weeks. - AZHeat 17:28:17 12/03/07 Good Luck. I know you've put alot of time and energy into - Gordo 93TT Daytona 07:57:04 12/04/07 Well, actually, some modern lawnmower-type engines - RSR 18:10:22 12/03/07 I've overhauled a couple - BlackholeZ 18:49:50 12/03/07 no...the crank and rod bearings must be pressure fed (n/m) - aliaZ 13:49:24 12/03/07 Yeah, I am waiting to see your new oil pan - moxie (SF) 17:34:36 12/03/07 are you running race gas? (n/m) - aliaZ 13:47:25 12/03/07 No, i'm running standard high quality gas... - bubuche 02:22:46 12/04/07 you just found your problem - aliaZ 09:03:59 12/04/07
Post a Followup	You cannot reply to this message because you are not logged in.