Subject	'empirical'. So you actually collect data
Posted by	sparkie on November 27, 2007 at 10:30 PM
	This message has been viewed 85 times.
In Reply To	You have some emperical data to back this up? (n/m) posted by AZHeat on November 27, 2007 at 04:21 PM
Message	before you say things here? Matter of the fact, if you knew what the diffuser area do to compressor efficiency you will have known the answer to the original question. www.ztechz.net ICQ # 14337317
Follow Ups	Machined my turbo to adapts Labree downpipe split parts??? - JFRacing 11:02:27 11/27/07 Leave the part off the downpipe. (n/m) - Woody75 (Denver) 11:06:05 11/27/07 Tuff call, but I think I'd avoid machining the turbo - Barry'z (NJ) 11:08:59 11/27/07 2nd. (n/m) - TheTwinZ (Peru) 11:11:55 11/27/07 it's not a tough call. The piece on the DP is easily removed - Spee 11:12:37 11/27/07 Re: it's not a tough call. The piece on the DP is easily removed - JFRacing 11:18:50 11/27/07 Is there any benefit to a better seal than the one - Barry'z (NJ) 11:22:27 11/27/07 Re: Is there any benefit to a better seal than the one - JFRacing 11:24:38 11/27/07 Re: Is there any benefit to a better seal than the one - JFRacing 11:27:57 11/27/07 Look at the picture of his turbo. It is not - AZHeat 11:40:14 11/27/07 Re: Look at the picture of his turbo. It is not - JFRacing 11:46:56 11/27/07 remove the dp piece... and i know this is off topic but - nobodylikeswoody 11:36:45 11/27/07 Don't modify the turbine housing - sparkie 11:43:31 11/27/07 Exhaust overflow? It is all merging into the - AZHeat 11:48:20 11/27/07 So? - sparkie 13:08:33 11/27/07 You have some emperical data to back this up? (n/m) - AZHeat 16:21:41 11/27/07 'empirical'. So you actually collect data - sparkie 22:30:19 11/27/07 Compressor <> Turbine . Guess that means "NO" amundo. (n/m) - AZHeat 23:12:26 11/27/07 Re: Don't modify the turbine housing - JFRacing 11:48:50 11/27/07 Re: Re: Don't modify the turbine housing - sparkie 22:18:26 11/27/07 Re: Re: Re: Don't modify the turbine housing - JFRacing 06:54:03 11/28/07 Good luck getting the turbine housing to bolt up... - jickel180 13:03:14 11/27/07 Re: Good luck getting the turbine housing to bolt up... - JFRacing 14:51:07 11/27/07 Re: Good luck getting the turbine housing to bolt up... - JFRacing 14:58:15 11/27/07 Re: Machined my turbo to adapts Labree downpipe split parts??? - JFRacing 15:00:18 11/27/07 Any more pics of your manifold setup? Looks good. - jickel180 15:18:18 11/27/07 Re: Any more pics of your manifold setup? Looks good. - JFRacing 17:17:56 11/27/07 My previous GT28R turbos were like that.. - Kong ZTT GT28RS MD 21:47:55 11/27/07
Post a Followup	You cannot reply to this message because you are not logged in.