Subject	Re: it's not a tough call. The piece on the DP is easily removed
Posted by	JFRacing on November 27, 2007 at 11:18 AM
	This message has been viewed 67 times.
In Reply To	it's not a tough call. The piece on the DP is easily removed posted by Spee on November 27, 2007 at 11:12 AM
Message	:No machining necessary. I know this piece easily removed but for the best perfomance. The piece in my turbo not shut off completly space betwen turbo and downpipe. No performance probleme if i just removed this pieces???
Follow Ups	Machined my turbo to adapts Labree downpipe split parts??? - JFRacing 11:02:27 11/27/07 Leave the part off the downpipe. (n/m) - Woody75 (Denver) 11:06:05 11/27/07 Tuff call, but I think I'd avoid machining the turbo - Barry'z (NJ) 11:08:59 11/27/07 2nd. (n/m) - TheTwinZ (Peru) 11:11:55 11/27/07 it's not a tough call. The piece on the DP is easily removed - Spee 11:12:37 11/27/07 Re: it's not a tough call. The piece on the DP is easily removed - JFRacing 11:18:50 11/27/07 Is there any benefit to a better seal than the one - Barry'z (NJ) 11:22:27 11/27/07 Re: Is there any benefit to a better seal than the one - JFRacing 11:24:38 11/27/07 Re: Is there any benefit to a better seal than the one - JFRacing 11:27:57 11/27/07 Look at the picture of his turbo. It is not - AZHeat 11:40:14 11/27/07 Re: Look at the picture of his turbo. It is not - JFRacing 11:46:56 11/27/07 remove the dp piece... and i know this is off topic but - nobodylikeswoody 11:36:45 11/27/07 Don't modify the turbine housing - sparkie 11:43:31 11/27/07 Exhaust overflow? It is all merging into the - AZHeat 11:48:20 11/27/07 So? - sparkie 13:08:33 11/27/07 You have some emperical data to back this up? (n/m) - AZHeat 16:21:41 11/27/07 'empirical'. So you actually collect data - sparkie 22:30:19 11/27/07 Compressor <> Turbine . Guess that means "NO" amundo. (n/m) - AZHeat 23:12:26 11/27/07 Re: Don't modify the turbine housing - JFRacing 11:48:50 11/27/07 Re: Re: Don't modify the turbine housing - sparkie 22:18:26 11/27/07 Re: Re: Re: Don't modify the turbine housing - JFRacing 06:54:03 11/28/07 Good luck getting the turbine housing to bolt up... - jickel180 13:03:14 11/27/07 Re: Good luck getting the turbine housing to bolt up... - JFRacing 14:51:07 11/27/07 Re: Good luck getting the turbine housing to bolt up... - JFRacing 14:58:15 11/27/07 Re: Machined my turbo to adapts Labree downpipe split parts??? - JFRacing 15:00:18 11/27/07 Any more pics of your manifold setup? Looks good. - jickel180 15:18:18 11/27/07 Re: Any more pics of your manifold setup? Looks good. - JFRacing 17:17:56 11/27/07 My previous GT28R turbos were like that.. - Kong ZTT GT28RS MD 21:47:55 11/27/07
Post a Followup	You cannot reply to this message because you are not logged in.